Manual Scheppach Bestcombi 5.0 (page 30 of 48) (English, German, French)

782113

Zoom out

Zoom in

1/48

54A

6.7 Réglage des fers (54-54A)

Mettre la machine hors tension, basculer le protecteur cache-lame et

retirer le guide de dégauchissage.

Régler la table d’entrée à une passe de 2 mm.

Débloquer le fer en vissant légèrement les vis extérieures du serre-lame.

Immobiliser 2 planchettes de bois dur bien dégauchies sur la table de sortie.

Tourner l’arbre machine pour positionner le fer à sa position la plus haute

(aligner sur les repères V marqués sur le bâti).

Le porte-fer en appui sur la tête de vis de réglage en fond rainure de l’arbre,

faire monter le fer contre la planchette en dévissant la vis de réglage avec

une clé mâle 6 pans de 3 mm (55).

Egaliser et bloquer le porte-fer et refaire un contrôle des fers.

6.7 Hobeleisen einstellen (54-54A)

Die Maschinen vom Stromnetz trennen.

Schutzhaube nach oben schwenken und Abrichtanschlag abnehmen.

Einschubtisch zur 2mm-Schnittstärke stellen.

Hobeleisen lösen : Äußere Schrauben des Messer-Einspanners leicht

andrehen.

2 gut abgerichtete Hartholzleisten auf den Abnahmetisch befestigen.

Die Antriebswelle drehen um die Schneide des Messers in seine höchste

Position zu bringen (auf Markierung V des Gehäuses).

Indem der Messerhalter auf dem Schraubenkopf in der Lagerung auiegt,das

Messer bis zum Anstoß der Leiste durch aufdrehen der Stellschraube bringen

(mit einem Allen Hex Key 6 - 3 mm) (55).

Messer und Halter mit dem Einspanner ausgleichen und blockieren.

6.7 To adjust the knives (54-54A)

Disconnect the machine from the power

Lift up the guard bridge and remove the planer fence.

Set the infeed worktable for a cut of 2mm.

Release the knife by screwing slightly the screws at the ends of the blade

holder.

Clamp 2 well planed planks of hard wood onto the outfeed worktable.

Turn the cutter block to bring the knife edge to the upper position (in line of

the marks V engraved on the machine basis).

With the support bar pressing down of the adjusting screw top (in the slot

base), unscrew the adjusting screw by using an Allen Hex Key 6 - 3 mm to

bring the knife up to the plank (55).

Level and lock the support bar and check again the knife setting.

55A

The machine is delivered with reversible throwaway knives.

Should the sharpness look bad, turn the knives to use the second sharp edge.

6.8 To replace the knives (55-55A-55B)

Tighten the screws of the blade holder (55A-1). Remove the support bar with

the knife (55A-2). If needed, take out the blade holder for cleaning.

Separate the knife from its support and clean each part (55A-3).

Place the knife on the pins of the support bar with the edge in the right direction

(55B-a) and insert the assembly into the seating level the knive with the blade

holder (55B-b). Level with the blade holder (55B-c), then lock by releasing

alternately the screws (the exterior screws rst), nally lock the knife

(maxi 15N/m).The cutter blade holder and the corresponding seating are

marked 1 , 2 , 3 : Respect this order.

D’origine la machine est équipée de fers réversibles et jetables. Lorsque les

fers ne sont plus affûtés, les inverser pour utiliser le deuxième côté tranchant.

6.8 Remplacement des fers (55-55A-55B)

Visser les vis du serre-lame (55A-1).

Retirer l’ensemble porte-fer (55A-2). Si besoin, démonter le serre-lame pour

son nettoyage.

Séparer le fer de son support pour son nettoyage (55A-3).

Positionner le fer sur les ergots du porte-fer en orientant le tranchant (55B-a)

et engager l’ensemble dans son logement (55B-b).

Egaliser avec le serre-lame (55B-c), puis bloquer en dévissant progres-

sivement les vis en commençant par l’extérieur, puis dénitivement (maxi

15N/m). Les serres-lames et leur logement respectif sont repérés 1 , 2 , 3 :

veiller à conserver cet ordre.

Die Maschine ist werkseitig mit Einwegmessern mit doppelseitigen Scheideä-

chen bestückt. Bei stumpfen Messern, können diese gewendet werden um die

zweite Schneideäche zu benutzen.

6.8 Hobeleisen auswechseln (55-55A-55B)

Die Schrauben des Messer-Einspanners lösen (55A-1).

Hobeleisen mit Messerhalter heraus nehmen (55A-2). Bei Bedarf, den Messer-

einspanner zum reinigen heraus nehmen (55A-3).

Messer auf die Nuten des Halters setzen, dabei auf die Richtung der Schneide-

äche achten (55B-a) und das gesamte Teil in die richtige Lagerung der

Antriebs-welle einsetzen (55B-b) : Markierung 1 , 2 , 3 auf Messer-Einspanner

und Welle beachten.Hobeleisen an den Einspanner genau anpassen (55B-c)

und klemmen : Schrauben nach und nach aufdrehen (mit den äußersten b

ginnen) (maxi 15N/m)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Bestcombi 5.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 6.33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Bestcombi 5.0 Manual

Product: