782109
24
Zoom out
Zoom in
Previous page
1/35
Next page
Error search plan
Failure Possible cause Remedy
Saw
Machine vibrates Clamping lever for height adjustment is not screwed tightly Tighten clamping lever
Tool is not screwed tightly Tighten tool
Unclean cuts / wood burns Tool is blunt Use sharp tools only
Tool is not installed correctly Check correct installation of the tool
Fast wear and tear fo tool Tool is sharpened incorrectly Have the tool re-sharpened correctly / install new tool
Covered wood (cement, sand, nails) Use clean wood only
Motor heats up (one can no
longer touch it with bare hands,
it switches off constantly)
Different causes possible Get it checked by an electrician
Machine stops Feed is too fast Reduce feed
Tool is blunt Use sharp tools only
The wood is lifted high by the
rear part of the saw blade
Longitudinal stop is not parallel Readjust longitudinal stop
Splitting wedge not in alignment or sewing is too weak Readjust splitting wedge
Height adjustment of the spindle
is stiff
Threaded rod, toothed wheels, slide rails are polluted Clean and lubricate components
Clamping lever is not loosened Check and loosen clamping lever
Milling machine
Machine vibrates Clamping lever for height adjustment is not screwed tightly Tighten clamping lever
Tool is not screwed tightly Tighten tool
Unclean cuts / wood burns Tool is blunt Use sharp tools only
Tool is not installed correctly Check correct installation of the tool
Fast wear and tear of tool Tool is sharpened incorrectly Have the tool re-sharpened correctly / install new tool
Covered wood (cement, sand, nails) Use clean wood only
Motor heats up (one can no
longer touch it with bare hands,
it switches off constantly)
Different causes possible Get it checked by an electrician
Machine stops Feed is too fast Reduce feed
Tool is blunt Use sharp tools only
Height adjustment of the spindle
is stiff
Threaded rod, toothed wheels, slide rails are polluted Clean and lubricate components
Clamping lever is not loosened Check and loosen clamping lever
Jointer and planer
Motor does not stop Incorrect position of the control button Check the position of the control buttons
No power Connect machine to the mains power supply
Power failure Get it checked by an electrician
Position of vacuum suction sensor is incorrect Check position, readjust if necessary
Machine tables are too rigid to
actuate
Threaded rod, toothed wheels, slide rails are polluted Re-lubricate components
Working speed is unusally slow Tool is blunt Use sharp tools only
Cut deep to big Reduce cutting thickness
Polluted drive rollers Clean working rollers
Table is not clean or is damaged Clean table
Belt slips Re-stratch belt
Machine vibrates Blunt or poorly belt tool Install new tool / re-adjust
Differences in the dimensions of the tool Mark tools in sets
Uneven base Adjust table legs
Formation of recess or
workpiece is not straight after
planing
Tool is set higher than the transporting table Set tool correctly
Improper laying or poor support of workpiece on the machine Place tool carefully
24
DGB
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Bestcombi 310 Kity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Bestcombi 310 Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info