Manual Scheppach Bestcombi 310 Kity (page 23 of 35) (English, German, French)

782109

Zoom out

Zoom in

1/35

ON and OFF switch Fig. A 8

Each ON switch allows the start of its own

function

Set master switch (T) in the milling mode (see

icons on the switch box)

Green button - Activate

Red button - Deactivate

In case of danger, press lateral Emergency-Stop

switch

Caution: To start a function, one must unlock the

stop switch without fail.

Slide carriage Fig. B 7

The slide carriage is fully installed.

To unlock, pull out the button (5) laterally on the

table, rotate ¼ turn to the right and re-engage.

Delivery table Fig. B 8

Install table (6) if necessary, laterally with 2

tommy screws.

Slide carriage with clamping device and

angle setting Fig. 8

Introduce angle stop (7) into the groove of the

slide table with the guide bar and tighten with

the turning handle (9).

For angle settings, loosen the tommy screws

(10), set angle and tighten again.

Place the tool clamp (11) in the opened state

over the workpiece, tighten the clamping screw

(12) and clamp the workpiece with the eccentric

lever (13).

Installation and operation of the jointing and

planing machine

3.0 Jointer and planer (C)

A Adjustable jointing table

B Jointing support table

C Adjusting wheel for cutting depth

D Jointing stop

E Planer shaft protection

F Vacuum suction hood

G Height adjustment wheel of planing table

H Planing table

I ON and OFF switch

Caution: Disconnect the power plug before

performing adjustment and retrotting jobs.

Jointing Figure. C1

The vacuum suction hood (F) is installed perma-

nently under the jointing table (B)

Plug in vacuum suction hose (D 100 mm)

Detach the feed rollers with the help of lever (1)

to avoid unnecessary wear and tear

Setting the jointing stop Fig. C2 and C3

Remove cover plate (2) between jointing table

and milling table

Install guide section (3) with 2 Allen screws (3)

Insert stop guide (5) and tighten with tommy

screw (6)

Insert the stop bar (7) in the stop guide (5), with

carriage bolt

And fasten tommy screw (8)

By loosening the tommy screw (6) the stop

can be moved along the entire width

of the jointing table

The stop rail can be inclined up to 45°, to do this,

loosen the clamping screw (8), adjust angle and

re-tighten

Caution! Tighten all the parts well again after

each setting.

Setting the planer shaft cover

The planer shaft cover must always be set such

that it covers the section of the planing shaft that

is not being used.

Caution: Use slide rod.

For at workpieces, adjust the height of the co-

ver such that the workpiece can be slided under

the guard.

For strong workpieces that cannot be covered,

use the slide handle.

Setting the cutting depth Fig. C4

The handle (6) can be used to change the height

of the adjustable jointing table 1 increment = 1

The cutting depth can be read on the scale (7)

Planing

Conversion from jointer to planer Fig. C5

and C6

Remove the jointing stop

Detach the clamping lever (8) under the adjus-

table jointing table

Tilt table laterally in the outer direction

Detach the clamping lever (8) under the jointing

table and tilt the table with the planer shaft cover

laterally in the outer direction

Fold the vacuum suction hood (F) upwards and

engage

Connect the vacuum cleaner hose.

Setting of table height Fig. C6

Set the planing table (H) with the height adjust-

ment wheel (G) to the workpiece size

with the help of the scale (9) and clamp tightly

with the tommy screw (10).

Cutting depth 1 rotation = 3mm

Automatic wood feed Fig. C7

Switch on feed roller with lever (11)

In case of danger, switch the Emergency-Stop

switch (12)

ON and OFF Fig. C8

Set machine to planing on the switchbox (Fig.

1.0 A) and on the

Feed side during planing

Green button (13) - Activate

Red button (14) - Deactivate

Planer knife replacement Fig.C9

Caution: Disconnect the power plug before

performing adjustment and retrotting jobs.

Fold planer knife guard down

Loosen 5 clamping screws (15) and remove

planer knife (16) with holder (17)

Clean all the parts, insert a new planer knife

with holder

Setting the knife

Set adjustable jointing table to 2 mm cutting

thickness

Mount 2 well jointed wood strips on the pick-up

table

Turn the planer shaft to bring the cutter of the

knife to its highest position

Set the height with the 2 adjusting screws (18)

and tighten the clamping screws.

Checking settings Fig. C10 and C11

Place a jointed bar (19) on the pick-up table and

mark the position (a).

By turning the planer shaft, the cutting edge of

the knife should move the bar (19) by 2-3 mm.

Position (b)

This test must be conducted for each knife on

the left and right sides.

A smooth and trouble-free planing is guaranteed

if the execution is accurate.

Accessoires

Cross-table with telescopic arm .............................................................................. Art. Nr. 1902103701

Bend milling stop .......................................................................................................Art. Nr. 1902403702

Pin cutting device ...................................................................................................... Art.Nr. 3300454742

HS-Planer knife ..........................................................................................................Art.Nr. 3304000004

Swivel plates of HS-planer knife ..............................................................................Art.Nr. 3304200023

Knife holder ................................................................................................................ Art.Nr. 3304300033

DGB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Bestcombi 310 Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Bestcombi 310 Kity Manual

Product: