Manual Scheppach BCH5300BP (page 29 of 84) (English, German, Dutch, French, Italian, Polish)

781392

Zoom out

Zoom in

1/84

29GB

2. Turn the engine switch (6) to the ON position. Fig.

30, 31

3. Put the choke lever on the position. Fig. 31

4. Press the fuel pump more than 5 times. Fig. 32

5. Pull the recoil starter handle (11) 3-5 times to

start the engine. Fig. 33

6. Pull the rope until engine starts. Fig. 33

7. Wait a while adjust the choke lever to posi-

tion. Fig. 34

8. To start the cutting tools, operate the release le-

ver (7) with the palm of your hand, and the throttle

lever (8) with your ngers. The further you push

the throttle lever, the higher the motor speed.

When releasing the throttle lever, the motor be-

comes idle and the cutting tools stop. Fig. 30.

The cutting tools should not continue turning and

should not move when the motor is idle. Fig. 30

9. Adjusting line length when working:

This machine is tted with a “Tap & Go” head.

To release more line, tap the cutting line head

against the round with engine at top speed: the

line will be released automatically and the knife

cut off the excess length. Fig. 48

10. If meet any problems, press the engine switch to

off position, the machine will stop running. If need

stop cutting head working, release the throttle le-

ver (8). Fig. 30

11. In an emergency, the safety button (m) can be

pressed from the harness. The machine then de-

taches immediately from the carrying strap and

falls to the ground. Fig. 28

12. If the machine is hot, the throttle level can be ad-

justed to ON position directly when re start the

machine.

Note: If the engine does not start up even after sev-

eral attempts, read the section „Engine troubleshoot-

ing“.

Note: Always pull the starter cord out in a straight

line. If it is pulled out at an angle, then friction will oc-

cur on the eyelet. As a result of this friction, the cable

will become frayed and will wear away faster. Always

hold the starter handle when the cable retracts.

Never allow the cable to snap back when it has been

pulled out.

Note: Do not start the motor in tall grass.

m Attention: When the engine has been switched

off, the cutter continues running for several seconds

therefore do not close to cutting head of brush cutter

until the cutter has come to a standstill!

9. Working instructions

Extending the cutting line

Caution! Do not use any kind of metal wire or metal

wire encased in plastic in the line spool. This may

cause serious injuries to the user. To extend the cut-

ting line, run the engine at full speed and tap the line

spool on the ground. This will automatically extend

the line. Fig. 48

The blade (A) on the safety shield will cut the line to

the appropriate length. Fig. 24

mImportant: Remove all grass and weed remnants

at regular intervals to prevent the shaft tube over-

heating. Lawn, grass and weed remnants become

trapped under the safety shield and prevent the shaft

tube from receiving adequate ventilation. Remove

the remnants carefully using a screwdriver or the like.

Fig. 49

Different cutting methods

When the equipment is correctly assembled it will cut

weeds and long grass in places which are dif cult

to access, e.g. along fences, walls and foundations

and also around trees. It can also be used for „mow-

ing“ down vegetation so that a garden can be better

prepared or a certain area cleared down to the soil.

Fig. 50

m Attention: Even if it is used carefully, cutting

around foundations, stone or concrete walls, etc. will

result in the line suff ering more than normal wear.

Trimming/mowing

Swing the trimmer from side to side in a scything

motion. Always keep the line spool parallel to the

ground. Check the site and decide which cutting

height you require. Guide and hold the line spool at

the required height to obtain an even cut. Fig. 50

Low trimming

Hold the trimmer right in front of you at a slight angle

so that the underside of the line spool is above the

ground and the line strikes the correct target. Always

cut away from yourself. Never draw the trimmer to-

wards yourself.

Cutting along fences/foundations

Approach wire mesh fences, lath fences, natural

stone walls and foundations slowly so that you can

cut close to them without striking the obstacle with

the line. If, for example, the line strikes stones, stone

walls or foundations, it will wear or fray. If the line

strikes wire fencing, it will break.

Trimming around trees

When trimming around tree trunks, approach slowly

so that the line does not strike the bark. Walk around

the tree, cutting from left to right. Approach grass or

weeds with the tip of the line and tilt the line spool

forwards slightly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BCH5300BP in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 7.53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach BCH5300BP Manual

Product: