781452

Scheppach ASP50-ES Manual

19
Zoom out
Zoom in
Previous page
1/88
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 19
m IMPORTANT!
The device is not suitable for vacuuming ammable
liquids. For wet vacuuming, use the only the foam l-
ter (22) provided.
Drain hose (11) (g. 20)
The stainless steel container (15) is equipped with
a water drain hose (11) in order to make it easier to
drain. To do so, pull the stopper (7) out of the drain
hose (11) and drain off the liquid. Then insert the stop-
per (7) again.
9. Maintenance and cleaning
m WARNING!
Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
Cleaning
It is recommended to clean the device after each use.
Do not spray the device with water or clean it under
running water. This can result in electric shocks and
can damage the device.
Empty the stainless steel container (15) after each
use: After opening the stopper in the drain hose (7),
the liquid collected can be drained out. Residual liq-
uid remains in the stainless steel container (15). To
remove residual liquid, take off the machine head (2)
by releasing the locking hooks (5) from the stainless
steel container (15). Pour out the liquid residue. Clean
the container with a damp cloth.
• Replace paper lter bag when full
• Always keep the device clean. Do not use cleaning
agents or solvents.
• Keep the ventilation slots clean and free of dirt and
dust.
• Clean the device only with a soft brush or a damp
cloth.
• Clean the foam lter (22) with a little soap and run-
ning water and then leave it to air dry.
Maintenance
The device is maintenance-free.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables. Wear parts*: Foam lter, Paper lter
bag, Folded lter for dry vacuuming
* Not necessarily included in the scope of delivery!
Blowing:
Connect the suction hose (21) to the blowing func-
tion connection port (19). Slide the end of the suction
hose (21) with the two nipples into the blowing func-
tion connection port (19). Insert the two nipples into
the recesses. It is not necessary to turn it here.
Installing the metal extension tube (27), suction
hose (21) and nozzles (25/26) (g. 16, 17)
• Connect the metal extension tube (27) with the
bent end of the suction hose (21).
• Fit the oor nozzle (25) or joint nozzle (26) to the
other end of the metal extension tube (27).
• Push the slide piece forwards (A) to change the
length of the metal extension tube (27). (Fig. 17)
• Pull the tube to the desired length (B). Ensure that
the slide lock latches into place. (Fig. 17)
8. Operation
m WARNING!
Switch the device off if liquid or foam emerges with
the exhaust air during wet vacuuming.
Switch on / switch off / automatic (g. 18, 19)
The ON/OFF switch (18) has three settings:
1 switch setting 0: Off
2 switch setting II: On
• Press the on/off switch (18) to switch on.
• Press the on/off switch (18) again to switch the de-
vice off.
3 switch setting I: Automatic mode (the vacuum
cleaner will be switched on by an electric tool).
• Plug your electrical tool’s cable into the automatic
socket (g. 19).
• Connect the suction hose to the suction connection
on your electrical tool.
• Check that the connection is secure and airtight.
• Set the switch on the vacuum system to position “I”
= Automatic mode.
Dry vacuuming (g. 3, 12, 13)
Use the folded lter (24) for dry vacuuming. The pa-
per lter bag (23) can be used in addition. This en-
sures that the folded lter (24) remains free of dust for
longer and maintains the vacuum power for longer.
In addition, the disposal of the dust is also easier.
Always ensure that the lters are correctly tted.
Wet vacuuming (g. 3, 11)
Use the foam lter (22) for wet vacuuming. Ensure
that the foam lter (22) is correctly tted.
If the stainless steel container (15) is full, the safety
oat valve (20) closes the suction port and suction
operation is interrupted.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach ASP50-ES at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach ASP50-ES in the language / languages: English, German, Dutch, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 4.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info