Manual Scheppach AB1500 (page 19 of 108) (English, German, Danish, French, Italian, Polish, Finnish)

781880

Zoom out

Zoom in

1/108

Ibrugtagning

Placer mejsel g. 2,3

• Rengør værktøjet før indsættelse, og smør værk-

tøjsskaftet med lidt fedt.

• Træk SDS MAX-spændepatron-låseanordning (4)

tilbage til anslag. Indsæt mejsel til anslag, og drej

indtil den går i indgreb.

• Slip SDS MAX-spændepatron. Mejslen må kun

forskydes ca. 1 cm frem eller tilbage i spændepa-

tronen.

• Kontrollér låseanordningen ved at trække i værk-

tøjet.

Udtagelse af værktøj

Udtagelsen foregår i omvendt rækkefølge.

Ekstra håndtag g. 4,5

Mejselhammeren må af sikkerhedsmæssige årsager

kun bruges med det ekstra håndtag.

Det ekstra håndtag (3) giver yderligere hold ved anven-

delsen af mejselhammeren. Apparatet må af sikkerheds-

mæssige årsager ikke anvendes uden det ekstra håndtag

(3). Det ekstra håndtag kan drejes til alle positioner. Løsn

låseanordningen for det ekstra håndtag (3). Drej grebet

til den arbejdsposition, som er mest behagelig for dig,

og spænd igen skruerne.

Betjening/arbejdsinstruktion

Bemærk! For din egen sikkerheds skyld må maski-

nen kun holdes i de to håndtag (1 og 3, g. 1)!

Dette forhindrer risikoen for stød, hvis du rammer elek-

triske ledninger under mejslingen.

Tænd og sluk (g. 6)

Dette elektriske værktøj arbejder med momentafbry-

delse.

Advarsel! Hold godt fast i det elektriske værktøj ved

hovedhåndtaget eller det ekstra håndtag! Betjen først

derefter ind-/udkobleren! Ellers er der fare for tilskade-

komst!

Hold godt fast i det elektriske værktøj i vertikal position

ved hovedhåndtaget eller det ekstra håndtag.

Tryk på ind-/udkobleren, og hold den i position.

Slip ind-/udkobleren for at slukke for det elektriske værk-

tøj.

• Tryk samtidigt på ind-/udkobleren (2) og låseanord-

ningen (a) ved håndtaget mhp. konstant drift.

• Tryk på ind-/udkobleren (2), og slip den igen for at

deaktivere den konstante drift.

Getting started

Using the chisel Fig. 2,3

• Clean the tool before tting it and apply a thin coat-

ing of grease to the tool shaft.

• Pull back the SDS MAX chuck lock (4) as far as

possible. Insert the chisel as far as possible and

turn it until it locks.

• Release the SDS MAX chuck lock. It should only

be possible to move the chisel in the drill chuck by

approximately 1 cm forwards or backwards.

• Check the lock by pulling the tool.

Removing the tool

To remove the tool, proceed in reverse order.

Additional handle Fig.4,5

For safety reasons you must only use the demolition

hammer with the additional handle.

The additional handle (3) enables you to achieve better

stability whilst using the demolition hammer.

For safety reasons the machine must not be used with-

out the additional handle (3).

The additional handle can be turned into any required

position. Undo the lock of the additional handle (3). Then

turn the handle into the most comfortable working posi-

tion and tighten the screws again.

Operation / work instructions

Caution! For your safety, the machine must be held

only at the two handles (1 and 3, Figure 1)!

This will avoid the danger of an electric shock through

contact of lines during chiselling.

Switching on / off (Fig. 6)

This power tool workes with torque switching.

Warning! Hold power tool safely on the main and

additional handle! Press until the power button! Other-

wise there is a risk of injury!

To switch on: Press the control switch (2).

To switch off: Release the control switch (2).

• For continuous operation, press the on/off switch

(2) and the locking button (a) on the handle at the

same time.

• To switch off continuous operation, press the on/off

switch (2) and then release it again.

Always keep the chiselling tools sharp.

Note:

– Work only at low pressure when chiselling.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach AB1500 in the language / languages: English, German, Danish, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 4.53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach AB1500 Manual

Product: