699462

Satel VERSA-LCDM-WRL Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
4 VERSA-LCDM-WRL SATEL
You can add the wireless keypad to the ABAX system by using either a computer with DLOADX
program installed, or an LCD keypad. The controller allows for registering of up to 6
VERSA-LCDM-WRL keypads. If no wired keypad is connected to the control panel, you can only add
the first wireless keypad using the DLOADX program (to establish communication between the
program and the control panel, you must start the service mode “from pins” – refer to the control panel
programming manual).
3.1.1 DLOADX program
You can add wireless keypads in the “VERSA – Structure” window, “Hardware” tab, after clicking on
the name of ABAX system controller on the list of devices, and then on the “LCD-WRL” tab (see:
Fig. 3 p. 5).
1.
Click on the “Read” button to read the data related to wireless keypads from the controller (these
data are not read after clicking on the
button in the main menu).
2. Click on the “New device” button. The “
New wireless dev.”
window will open.
3. In the “Serial number” field enter the 7-digit serial number of the added device. The serial number
can be found on the electronics board.
4. In the “Address” field, select which address is to be assigned to the keypad to be added.
5. Press any button on the keypad or open its tamper switch.
6. The message will confirm that a keypad has been added (unless you have entered an invalid
serial number, of which you will be informed by a message). The name assigned to the keypad
will be displayed. You can change it.
7. Click “OK” (to cancel adding the keypad, click on the “Quit” button). The “
New wireless dev.”
window will close. The new keypad will appear in the table,
“LCD-WRL”
tab, as well as on
the list of expanders
.
8. Click on the “Write” button to write the new wireless keypad data to the controller (these data will
not be written after clicking on the
button in the main menu). The new keypad data will be
automatically written to the control panel.
3.1.2 LCD keypad
You can add wireless keypads in the service mode by means of the
N
EW DEVICE
function (
S
ERVICE
MODE
2. H
ARDWARE
1. K
PDS
.
&
EXPS
.
3.
W
IRELESS MOD
.
1. N
EW DEVICE
).
1. Having started the function, enter the 7-digit serial number of the added keypad and press the
key. The serial number can be found on the electronics board.
2. When the “Open device tamper” message is displayed, press any key on the keypad or open its
tamper switch.
3. Information on the keypad to be added will be displayed (if nothing happens, it can mean that you
have entered an invalid serial number – if this is the case, press
to return to the submenu).
Press
to confirm your intention to add a keypad.
4. Using the
and keys, select the address which is to be assigned to the keypad to be
added, and then press
. The wireless keypad will be added.
5. The name assigned to the keypad will be displayed. You can change it. Press
to save the
name.
6. In the next step, you can configure the settings stored in the ABAX system controller (see: p. 5).
3.2 Removing the keypad from the wireless system
3.2.1 DLOADX program
You can remove the wireless keypads in the “VERSA – Structure” window, “Hardware” tab, after
clicking on the name of ABAX system controller on the list of devices, and then on the “LCD-WRL” tab
(see: Fig. 3 p. 5).
1.
Click on the “Read” button to read the data related to wireless keypads from the controller.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA-LCDM-WRL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA-LCDM-WRL in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA-LCDM-WRL

Satel VERSA-LCDM-WRL User Manual - German - 12 pages

Satel VERSA-LCDM-WRL User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info