699462
4
Zoom out
Zoom in
Previous page
1/12
Next page
2 VERSA-LCDM-WRL SATEL
2. Description
Operating modes
The keypad can work in two modes:
active mode – started by pressing any key. Additionally, the active mode can be started automatically
when an alarm occurs or an entry delay, an exit delay or an auto-arming delay begins (see
description of the
W
AKE
-
UP
parameter, section “Settings stored in ABAX system controller” p. 5).
In this mode, the keypad operates in much the same way as the LCD wired keypad. The display is
ON and the backlight, LED signaling and sound signaling are active.
inactive mode – is started:
after 20 seconds since the last key press,
after preset time, if the active mode was started automatically (see description of the
W
AKE
-
UP
parameter, section “Settings stored in ABAX system controller” p. 5).
The purpose of the
inactive mode is to save energy. The display is off. Backlight, LED indication
and sound signaling are disabled (if a time different from 0 is preset for the
W
AKE
-
UP
parameter,
CHIME from zones will be signaled).
Support for proximity cards
The built-in
proximity card reader enables the system to be operated by using proximity cards (any
125 kHz passive transponder in the form of a card, tag, etc.). If the alarm system is not to be operated
by using the proximity cards, the reader can be disabled (thus reducing the battery consumption).
Periodic transmissions
Every 15 minutes, the
keypad sends a periodic transmission. The purpose of such transmissions is to
monitor presence and condition of the keypad.
Battery status control
The keypad controls the
status of the batteries. If the voltage is lower than 2.75 V:
low battery information is sent during each periodic transmission,
on entering the active mode, a low battery message will be displayed (the message will specify
which battery is to be replaced – the battery designation can be found on the electronics board,
after opening the enclosure).
The battery life depends on how the keypad is used. The more frequently the active mode is
entered, the quicker the batteries will be depleted.
3. Installation
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the batteries. The
manufacturer is not liable for the consequences of incorrect installation of the battery.
The used batteries must not be discarded, but should be disposed of in accordance
with the existing rules for environment protection.
The keypad is designed for indoor installation. The place of installation should be readily accessible to
the system users. When selecting the installation location, take into account the communication range
of the ABAX system.
1. Open the keypad enclosure (Fig. 2).
2
. Install the batteries and add the keypad to the wireless system (see: Adding the keypad to the
wireless sy
stem”).
3.
Put the cover on the catches and snap the enclosure shut.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA-LCDM-WRL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA-LCDM-WRL in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA-LCDM-WRL

Satel VERSA-LCDM-WRL User Manual - German - 12 pages

Satel VERSA-LCDM-WRL User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info