699073
74
Zoom out
Zoom in
Previous page
1/114
Next page
72 Programming SATEL
Confirm commands with “1” [Confirm with 1] if this option is enabled, the LCD keypad
will require, in case of some functions, additional confirmation with the key 1.
Clear messaging on alarm clearing [Autoabort msg.] with this option enabled, clearing
the alarm can automatically cancel messaging about this alarm, if the user clearing the
alarm has the TELEPHONE MESSAGING CANCELING right.
Return to menu from Service Mode [SM -> menu] if this option is enabled, exiting the
service mode will be followed by return to the user menu instead of to the basic operating
mode of the keypad.
Return to menu from menu Test [Tests -> menu] if this option is enabled, exiting the
user function available in the TESTS or CHANGE OPTIONS submenu will be followed by return
to the submenu instead of to the basic operating mode of the keypad.
Fast module bus communication [Fast exp. bus] it is recommended to enable this option
to speed up communication with the modules. The option should only be disabled in case
of extended security alarm systems, where electric interference may cause problems with
communication.
No module restart reports [No rest. mon.] when the option is enabled and the Contact ID
or SIA format is used for reporting, no event codes referring to module restarts will be sent
to the monitoring station.
Service message after tamper alarm [Inf.aft.tamper] when the option is enabled, after any
tamper alarm, the keypads can display on LCD display the message informing that service
maintenance is necessary. The message will be cleared after entering the service code
and confirming it with the key.
Backlight off on AC loss [No AC-no blght] when this option is enabled, the backlighting in
keypads can be automatically switched off in case of 230 V AC power loss.
Block keypad after 3 wrong codes [Blk aft.w.code] with this option enabled, entering an
invalid code (reading in an invalid card / DALLAS iButton) three times will block the keypad
(reader) for 90 seconds. After expiry of that time, each next entry of an invalid code (read-
in of an invalid card / DALLAS iButton) will block the device immediately.
Trouble memory until review [Troubl. memory] if the option is enabled, the trouble
memory can be signaled until it will be cleared (clearing the trouble memory is possible
when exiting the function of viewing troubles in the keypad or in the “Troubles window,
DLOADX program).
Do not show alarm if armed [Hide alarms] with this option enabled, no alarms will be
indicated in keypads during the armed mode.
Limit events [Events limit.] with this option enabled, while armed events from the same
source will be saved into the event log and reported to the monitoring station 3 times only.
Alarming zones review [View clear.al.] if this option is enabled, in the LCD keypad the
zones that triggered the alarm can be reviewed immediately after the alarm is cleared.
Grade 2 with this option enabled, the system operates as required by the EN 50131
standard for Grade 2, i.e.:
starting the arming procedure may be impossible, or, if started, the arming procedure
may fail, if some zones are violated in the partition, or there is a trouble in the system,
LCD keypads, partition keypads, proximity card arm/disarm devices and reader
expanders do not signal alarms,
the
LEDs in keypads indicate alarms only when code has been entered and
confirmed with the key,
the blinking LED in keypads means that there is a trouble in the system, some
zones are bypassed, or there has been an alarm,
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 128 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 128 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 128

Satel Integra 128 User Manual - English - 51 pages

Satel Integra 128 Installation Guide - English - 36 pages

Satel Integra 128 User Manual - German - 54 pages

Satel Integra 128 Additional guide - German - 121 pages

Satel Integra 128 Installation Guide - German - 38 pages

Satel Integra 128 Quick start guide - Dutch - 24 pages

Satel Integra 128 User Manual - Dutch - 52 pages

Satel Integra 128 Additional guide - Dutch - 121 pages

Satel Integra 128 Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info