699392
22
Zoom out
Zoom in
Previous page
1/28
Next page
20 INT-TSH SATEL
2EOL/NC
ZCOM
R1
R2
A
T
3EOL/NC
ZCOM
R1
R2
A
T
R3
M
Fig. 9. Numbering of EOL resistors (same for the NO detector).
T – tamper. A – alarm. M – masking.
The value of EOL resistors is programmable. Depending on the control panel to which the
keypad is connected:
INTEGRA: parameters of the EOL resistors should be defined for zones in a single keypad.
Value of the resistors R1 and R2 is to be programmed (numbering of the resistors is
shown in Fig 9). You can enter values from 500 to 15
k. The total resistance (R1+R2)
may not exceed 15 k. For the R2 resistor, you can program value 0. In such a case, the
value of resistors used in the Double EOL configuration must be equal to half the value
programmed for the R1 resistor (the value of one resistor must not be less than 500 ). By
default, the following values are programmed:
R1 = 1,1 k;
R2 = 1,1 k.
The resistor value for Single EOL configuration is the sum of R1 and R2 resistors.
INTEGRA Plus: parameters of the EOL resistors should be defined for the mainboard zones.
The same parameters will be set automatically for the zones in keypads in which the value
of EOL resistors is programmable. Therefore, the “EOL resistance value” tab is not
available.
7.2 Keypad connected to VERSA / VERSA Plus / VERSA IP control panel
To configure the keypad settings, you can use:
DLOADX program: “Versa – Structure” window “Hardware” tab “Expanders” branch
[keypad name]. The DLOADX program alone makes it possible to configure all the
settings.
keypad: SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 2. SETTINGS [keypad
name]. How to enter the service mode, refer to the section on programming the keypad
address by means of the service function (p. 5).
7.2.1 Parameters and options
Shown in square brackets are the names displayed on keypads.
Name – individual name of the keypad (up to 16 characters).
Tamper signaled in part. [Tamper in p.] – partition where alarm will be triggered in the event
of keypad tamper (opening the enclosure or disconnecting the keypad from the bus).
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel INT-TSH-BSB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel INT-TSH-BSB in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel INT-TSH-BSB

Satel INT-TSH-BSB User Manual - English - 20 pages

Satel INT-TSH-BSB Quick start guide - English - 2 pages

Satel INT-TSH-BSB User Manual - English - 19 pages

Satel INT-TSH-BSB Quick start guide - Dutch - 2 pages

Satel INT-TSH-BSB Installation Guide - Dutch - 20 pages

Satel INT-TSH-BSB Installation Guide - Dutch - 28 pages

Satel INT-TSH-BSB User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info