699578
19
Zoom out
Zoom in
Previous page
1/40
Next page
CA-6 SATEL 17
ON
operation time in minutes
6
OFF
operation time in seconds
ON
LATCH type output – signaling until cleared (operation time irrelevant)
7
OFF
programmable output operation time
ON
polarity +12V when the output is active
8
OFF
polarity 0V when the output is active
Note: The option of output assignment to the partition is to be used, when separate
sirens have to be assigned to individual partitions. If not assigned to a partition,
the alarm output will signal every alarm.
EXAMPLE:
programming the OUT1 output as the BURGLARY/FIRE ALARM type with 5 minutes
operation time and polarity 0V in active state
[12345] [#] - enter the service mode
[3][1] [#] - call the function. The LEDs 1-8 shows number of current output type (LEDs 1-4 shows
binary first digit, LEDs 5-8 – second digit). The blinking B LED signals the output type
being programmed
[0][2] [#] - enter and confirm the number of output function (the A LED starts blinking - operation
time programming)
[0][5] [#] - program and confirm the time (A and B LEDs start blinking - output option programming)
[6] - LED 6 goes on - the „time in minutes” option is activated
[8] [#] - LED 8 goes off - set the "polarity" = 0V and exit the function
Note: Choosing a partition in the options will determine which access code is to be
used to switch off siren or to control a zone. The same effect is provided by
defining a list of zones controlling the outputs.
FS32 - programming list of zones for OUT1 (BIT)
The function is used to program the output controlling zones. The selection of zones limits
the output operation only to the reaction to violation of those particular zones.
The zone selection should only be used when it is necessary to have separate
signaling for events from a specific zone or a group of zones. If no list of zones is
programmed, the control panel will assume by default that the output reacts to events from
any zone – for example, the BURGLARY alarm type output will signal alarms for each
control panel alarm zone. Of course, the zone function (reaction type) is taken into
consideration, e.g. the alarm signaling output does not react if the state of the arming zone
changes.
If the list of zones has been programmed the control panel will skip the programmed
selection of partitions.
The FS32 function is used to assign zones to the OUT1 output. The programming consists
in lighting up the LEDs which correspond to the zones. When the list is completed, it
should be confirmed.
FS33 - programming OUT2 output
The function allows for defining the basic parameters associated with the OUT2 output.
The programming procedure is the same as for the FS31.
FS34 - programming list of zones for OUT2 (BIT)
The function programs the list of zones associated with the OUT2 output. The
programming procedure is the same as for the FS32.
FS35 - programming OUT3 output
The function defines the basic parameters associated with the OUT3 output. The
programming procedure is the same as for the FS31.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info