699578
5
Zoom out
Zoom in
Previous page
1/36
Next page
CA-6 SATEL 3
The zones (input lines) can perform the following functions in the system:
00 exit/entry the violation of which, when in the armed mode, will start countdown of the entry
delay time and will enable the delay for INTERIOR DELAY type zones (violation of an
INTERIOR DELAY zone without prior violation of the ENTRY/EXIT zone will trigger an
alarm immediately). Upon violation, a “zone violation” code is sent to the report station
(it is possible to skip sending this message), and, after counting down the "entry delay
time" and triggering the alarm – a “zone alarm” code. The "entry delay" countdown can be
signaled in the keypad. It is possible to define automatically bypassing zones if no
ENTRY/EXIT zone is violated during the exit delay time. Because of its additional
functions, this zone type cannot be used as a common zone for both partitions.
01 delayedwhen violated in the armed mode, it starts delay countdown, after which an alarm is
triggered. It will not occur if the zone is disarmed before completion of the delay
countdown. Upon violation, a “zone violation” code is sent to the report station, after
counting down the entry delay time and triggering the alarm – a “zone alarm” code.
The delay is not signaled in the keypads.
02 interior delayed when violated in the armed mode after previous violation of the
ENTRY/EXIT zone, it behaves like a DELAY zone. When violated in the armed mode
without previous violation of the ENTRY/EXIT zone, it behaves like an INSTANT zone.
03 instant – when violated in the armed mode, it immediately triggers an alarm and sends a ”zone
alarm” message to the monitoring station.
04 day/night when violated in the armed mode, it behaves like an INSTANT zone, while when
disarmed, it will signal violation in the keypad (unless function is disabled FS20, second
set, option 3) and send a “zone violation” code to the station.
05 counting L1 when violated in the armed mode, it increases the status of the first of three
violation counters (a “zone violation code is sent to the station), until the number of
violations specified for that counter is exceeded (programming in FS7). Then the violation
triggers an alarm (a ”zone alarm” code is sent to the report station). By default, the count-
up time is set at 30 seconds. It is possible to program another counter count-up time
(FS123). If the preset number of violations is not reached within this time, it will be reset.
The next zone violation will start the add-up procedure all over again. The violations are
added up starting from zero, and the count-up time starts upon the first violation after
resetting the counter. The "counting L1" function can be assigned to more than one zone,
in that case violations of those zones will be summed up. The zone will trigger an alarm
upon exceeding the programmed number of violations added up by a given counter.
Alarm can also be triggered after resetting the counting zone counter, if the zone
associated with the given counter is still violated.
06 counting L2 operation identical as for the "counting L1", but changes the status of the
second of the three counters.
07 counting L3 operation identical as for the "counting L1", but changes the status of the third
of the three counters.
08 24H audible armed all the time, irrespective of whether the partition it is assigned to is
armed, or not. Each violation of this zone will trigger alarm on the “burglary alarm” type
outputs, in the keypad and will send a “zone alarm” code. It makes possible to create
tamper circuits and panic buttons.
09 24H auxiliary armed all the time, irrespective of whether the partition it is assigned to is
armed, or not. Each violation of this zone will trigger an alarm in the keypad and will send
a “zone alarm” code. It is intended for connecting detectors such as gas or flood sensors,
etc.
10 24H silent armed all the time, irrespective of whether the partition it is assigned to is armed,
or not. Violation of this zone will only send a “zone alarm” code to the monitoring station.
11 24H fire armed all the time, irrespective of whether the partition it is assigned to is armed,
or not; intended for the fire detectors.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info