699577
12
Zoom out
Zoom in
Previous page
1/60
Next page
10 Programming SATEL
Programming the service functions by means of keypad
In the LED keypads, the parameters being programmed are indicated with LEDs. In the LCD
keypads, the parameters being programmed are shown on the display. The way of
programming and data display in the keypad depend on the type of data entered with the
service function. The panel programming is based on three types of functions: bit (BIT), decimal
(DEC) and hexadecimal (HEX). The bit functions are used to program two-state parameters:
YES and NO (e.g. the functions of zone assignment to partition, options). The decimal functions
are used for programming data in the form of a few digits (for example, the test transmission
time - 4 digits, individual entry delay time of zones - 16 x 2 digits). The hexadecimal functions
are used to program hexadecimal data (e.g., monitoring codes).
BIT functions in the LED keypads
During programming with a bit function, the LEDs 1 to 8 show the current setting of particular
parameters (diode on - YES, off - NO). Pressing one of the keys [1] to [8] changes the state of
the corresponding diode. Having programmed 8 options, save them in the control panel using
the [#] key. If the programming function includes more parameters, the control panel will signal
with two short beeps acceptance of the first eight parameters, then it will go to the next set of
options, displaying their status on the LEDs 1 to 8. By means of the LEDs 9 to 12, the panel will
show which set of options is currently being programmed. When all the parameters have been
programmed, the control panel will signal exiting the function with four short a one long beeps.
The [
*
] key makes it possible to quit the function at any time without saving the changes in
currently displayed data.
BIT functions in the LCD keypads
After a bit function is called, the keys W X will change the cursor position and the keys ST will
the value of the bit at the cursor position. It is also possible to enter the desired bit number with
the numeric keys. Bit numbers 10-16 are entered by pressing [
*
] followed by the key with the
second digit. The combination of [
*
] and [#] terminates the function.
BIT functions with a list in the LCD keypads
After a bit function with a list is called in the first line of the display the function name will be
shown, while in the second line – the name of the first option in this function (e.g. System
options). The character indicates that the option is on. To change the switch state press any
numeric key. The keys ST will scroll the switch list. The [
*
] key makes it possible to quit the
function at any time without saving the changes.
DEC functions in the LED keypads
During programming with a decimal function the LEDs 1-4 show binary the first digit, LEDs 5-8 -
the second digit, while the LEDs 9-12 display binary the counter of digit pairs (see figure 1).
The programming consists in entering a two-digit number and confirming it with the [#] key.
Make sure that the entered data are correct, because the control panel does not verify
the input parameters and programming any wrong settings may result in malfunction of
the panel. The control panel will confirm acceptance of the data with two short beeps. When all
the parameters have been programmed, the function is exited which is signaled with four short
and one long beeps.
The [
*
] key makes it possible to quit the function at any time without saving the changes in
currently displayed data.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info