699577
14
Zoom out
Zoom in
Previous page
1/24
Next page
USER MANUAL CA-10
12
10 - problem with transmission to monitoring station
11 - not used
12 - output 4 trouble
The previously detected troubles are displayed on repeatedly pressing any key. The
[
*
] key cancels the troubles log viewing function.
Current trouble check-out [7]
When the control panel signals a trouble detection (the
[
TROUBLE
] LED is blinking),
you can activate the current trouble check-out function by holding down the key [7].
In the LCD keypad, information on the trouble will be displayed When there are more
troubles, you can scroll through all the detected troubles list by pressing the keys WS
or TX.
In the LED keypad on activating the function, the (the
[
TROUBLE
] LED and the LEDs
indicating current troubles turn on (lack of illumination of any of the 12 LEDs is also
indicative of a problem). Pressing any key stops the function.
Note: If the installer has activated the "Indicate trouble until cancelled" option, the
trouble indicator will be on until cancelled, even if the trouble cause has been
removed. The trouble will be cleared after the trouble memory viewing is
completed and the function is quitted by pressing the [#] key. Quitting the
function by means of another key will not cancel blinking of the
[
TROUBLE
]
diode.
The LEDs have the following meanings:
1 - output 1 trouble,
2 - output 2 trouble,
3 - output 3 trouble - no load (e.g., the siren wires are cut), or overload (short
circuit) - usually service intervention is required.
4 - 230V AC loss - the panel is equipped with a limited time battery backup; if the
AC power loss trouble occurs despite of an effective AC mains, service
assistance should be called.
5 - battery trouble - to check on the type of battery trouble, press the key [5] – the
LED 1 or LED 2 will show the type of trouble:
- LED 1 – the battery is not connected or almost discharged or the fuse
on the control panel board is out of order,
- LED 2 – the battery voltage is too low (lower than 12V under load) –
discharged battery. This state may last for several hours after the
system has operated without the mains supply (or after a discharged
battery is connected). The battery charging time depends on its
capacitance (the battery is charged with direct current about 350mA,
the time necessary for testing the battery status is approx.12 minutes).
6 - keypad power supply trouble - signals an installation fault; service
intervention is necessary (the trouble can only be displayed while
viewing the trouble log).
7 – time not set - occurs on powering down and restarting the control panel; the
clock should be set with user function 6.
8 - printer trouble - stands for "not-ready" status of the printer connected to the
control panel RS-232 port as a result of, e.g., paper out trouble or no
power supply. The RS-232 port is monitored if the installer activates
real-time event printout.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info