699577
9
Zoom out
Zoom in
Previous page
1/24
Next page
CA-10 SATEL
7
In some keypads, the numeric keys are provided with letters. They may help the user
memorize a code by associating it with a particular word (e.g. the „[5][6][2][7][2]” code
corresponds to the word „KOBRA”).
When creating a new user access code, the master user assigns a so-called authority
level to it , i.e. determines which of the panel functions are available to the particular
user, and which are not. Usually, an access code entered for the particular partition will
only control that specific partition.
Optionally, the installer can activate the so-called "global access code" function. When
selected, this option makes the user access codes accepted in all 4 partitions,
irrespective of where they were entered, but the particular user number will not be
recorded in the event log.
Arming [CODE][#]
Arming is only possible when the partition is not signaling alarm and is not already
armed:
[
ALARM
] and [
ARMED
] diodes are off.
In order to arm the system access code should be entered and confirmed by pressing
[#] key. If, while typing the code, user makes a mistake, [
*
] key should be pressed and
the code re-entered. The access codes should be entered very carefully. Giving
a wrong access code three times in sequence may activate the alarm which is recorded
in alarm memory log as „3 wrong codes alarm”.
If the code is entered correctly and arming is possible, the panel will confirm the entry
with three short beeps. At the same time the [
ARMED
] LED will start blinking, which
indicates the exit delay time.
The LCD keypad will display information on arming, as well as the name of the user
who activated the armed mode. It will be followed by information on the exit delay
countdown (provided such an option is provided by the installer). The partitions with
active exit delay countdown are also indicated by blinking of the corresponding LEDs.
The exit delay and the way of audible signaling operation should be determined by the
installer.
The panel may fail to arm the system if:
the panel is not ready for arming: there are specifically selected zones which
cannot be violated or tampered when the system is being armed and one of them
is violated or tampered at the time of arming - the panel will signal the situation
with three long beeps. In such a case, it is recommended to wait until all the zones
are ready (the LEDs 1-12 / 1-16 go out), and then arm the system again. If one of
the zones remains violated (one of the LEDs 1-12 / 1-16 is on, which may be
caused e.g. by a detector trouble) or tampered the armed mode can be activated
after bypassing that zone (with user function 4),
the access code is wrong - the control panel will signal the event with two long
beeps
the partition contains no armed type zones - the control panel signals the event
with two long beeps (access code is correct and allows, for example, to call user
functions)
battery trouble - three long beeps (proper option is selected to prevent the
system from being armed in case of battery trouble).
Quick arming [0][#]
The user can quickly arm the system without any access code by pressing the [0][#] key
sequence. The Quick Arming function can be disabled by the installer. This way of
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info