699577
17
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 15
The control panel power supply is fitted with:
battery status monitoring system with optional disconnection of discharged battery,
visual signaling of the battery testing/charging process (LED indicator on the main board),
changeover battery charging current (350 mA/700 mA).
The stabilized voltage of the control panel power supply is 13.6–13.8 V and is factory set.
Attention should be paid so as not to cause overloading of the control panel power supply in
the alarm system. It is advisable to make a load balance for the power supply. The total
current inputs for the consumers (detectors, keypads) and the battery charging current may
not exceed the power supply capacity. In case of a higher electric power demand,
an additional power supply can be used for some of the security system consumers
(e.g. APS-15, APS-30 manufactured by SATEL). Table 1 (at the end of this manual) shows
an example of estimated balance of current consumption by the system, and an example of
battery selection.
The CA-10 main board can be connected to an electric shock protection circuit (grounding).
The protective cable terminal is designated by the symbol.
The „neutral” wire of the 230 V AC mains supply must not be connected to the
grounding terminal. If the facility has no separate electric shock protection
circuit, this terminal must be left free.
The CA-10 control panel should be installed in an enclosed space with normal humidity of air.
The space should be fitted with an available permanent (not detachable) 230 V power supply
circuit with protective grounding.
The control panel can be mounted in the CA-10 OBU housing (this
housing comprises a transformer designed for operation with the
control panel power supply), which permits installation of a battery with
17 Ah capacity. Before the housing is secured to the base, it is
necessary to mount inside the housing plastic distance plugs, which are
intended for subsequent installation of the main board.
In case the plugs tend to slip out, the catches fixing the plug in the
housing need to be slightly bent aside (Figure 2). When inserting the
plug, press the central part of the head firmly in so that it is blocked in
the housing hole. It is advisable to make sure that the plug, when
pressed, does not slip out from the opening. During installation of the
housing, be careful so as not to damage the wires which will be passed
through the hole in its back panel.
When the housing is secured, you can install the control panel main board and proceed to
making the connections.
IMPORTANT: Do not connect the mains power supply and the battery, until all the remaining
connections are completed.
The control panel is power supplied from 230 V AC mains. Negligence or wrong
connection may result in electric shock and pose a threat to life!
Therefore, be particularly careful when hooking up the control panel. In the
process of installation and connection of the control panel, the cable to be used
for mains supply must not be alive!
Connection of keypads
The keypad is designed to operate indoors in normal humidity. It should be mounted straight
on a flat surface. The spring provided on the tamper contact must adhere to the base so that
the contact will open at an attempt to tear the keypad off the wall.
Figure 2.
PRESS IN
BEND ASIDE
BEND ASIDE
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info