699577
18
Zoom out
Zoom in
Previous page
1/43
Next page
16 Installer Manual SATEL
The control panel can operate both with LCD and LED keypads in any configuration.
Notes:
We recommend keypad CA-10 LED-S v1.2 or newer to be used, because older keypads
LED S may work incorrect with keypad LCD v3.08 and next version (it regards to the
CA-10 KLED-M keypads, which were produced earlier, as well).
Only zone expanders with version 2 are allowed (label dated February 1998 or later).
The LCD display is fragile. It can be broken if the keypad is dropped to the floor!
After power-up of the KLED-S keypad, and when the control panel quits the service mode,
the keypad will remain disabled and will not react to pressing any keys for 5 seconds.
During that time the system settings are being read, and the keypad backlight is blinking
with a high frequency. Simultaneously, the keypad restores the automatic mode of keypad
illumination. The mode can be changed with the user function by holding down the key [9].
The keypads should be connected to the control panel connectors COM, +KPD, DATA,
CLK1, CLK2, CLK3, CLK4. The connectors COM, +KPD and DATA are common for all
partitions, while the connectors CLK1, CLK2, CLK3 and CLK4 determine the partition the
keypad belongs to. Where the system will be operated with less than 4 keypads, they should
be connected starting from the CLK1.
The keypads should not be connected in parallel to one CLK signal (one partition two
keypads). It applies to all LCD keypads, as well as the CA-10 KLED-S keypads. The only
exception are the CA-10 KLED keypads, which may be connected in parallel.
Each keypad should be connected with a separate cable. The distance between the keypad
and the panel can be up to 200 m. Unscreened cables are recommended to be used for
connecting the keypads.
It is recommended to use an untwisted unshielded cable 8x0,5 mm
2
(do not use twisted pair
cables). With recommended cable, the following distances between keypad and control panel
may be used to ensure appropriate power supply:
Distance Connection
№ of cable cores
LCD keypad LED keypad
up to 50 m
Power supply & ground
CLK & DATA signals
2 x 1
2 x 1
2 x 1
2 x 1
50–100 m
Power supply & ground
CLK & DATA signals
2 x 2
2 x 1
2 x 1
2 x 1
100–200 m
Power supply & ground
CLK & DATA signals
2 x 4
2 x 1
2 x 1
2 x 1
The keypads may be power supplied from the +KPD panel connector only. This output
can also be used for power supply of the keypad connected detectors.
As the LCD keypad current consumption is larger than that of the LED keypad (particularly
with active illumination of the keypad and display), it is important that resistance of the power
supply and ground lead-ins be taken into account when planning the cabling installation.
Caution: The supply voltage measured across the terminal block of LCD keypad with active
backlighting should not be less than 11 V.
The keypad tamper contact has no connection with the system anti-tampering circuit. Its state
is defined by the control panel, based on the data received from the keypad. When the
control panel is in the service mode, the tamper contact is not controlled.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info