699577
14
Zoom out
Zoom in
Previous page
1/43
Next page
12 Installer Manual SATEL
Operation with the computer can be realized in two ways: in the „local mode” by means of the
RS-232 port with RJ socket (after connecting the CA-10 directly to one of the computer COM
ports), or in the remote mode”, via the telephone line (in this case the computer must be
equipped with a modem).
Programming the data of LCD keypad is available in the local mode through the RS-232 port
on the keypad board. The DLOAD10 program, delivered with the panel, supports both
operating modes.
The DLOAD10 program enables:
downloading (reading) all control panel parameters,
uploading (writing) new parameters to the control panel,
downloading (reading) the system event log,
ON LINE operation.
The program does not read or change the user access codes these are only
accessible through the user functions from keypads.
In the ON LINE mode, the computer displays current information on the system state,
including zone violations, active outputs, control panel clock, and selected partition state.
Provision is made for controlling the system in the same way as with a LED keypad.
The computer screen keypad works in parallel with the real keypads in partitions, therefore
commands for all partitions can be given from one place. The ON LINE mode also permits
downloading troubles and programming the clock.
Communication in the local mode (through the RS-232 port) is started with a special service
function (FS112). Connection can also be initialized without using the keypad (e.g. if it is
located far from the control panel and the computer). This can be achieved using the "Local
connection with…" command in the DLOAD10 program.
Communication through the telephone line can be initialized in three modes:
1) The computer calls the control panel, which after answering the call exchanges
handshake signals with the computer. When they are correct, the panel confirms
acceptance of the remote programming command, hangs up and calls back to the
computer using a number preprogrammed in the control panel. Prior to calling the
computer back, the panel notifies the monitoring station that the programming has
started.
2) The computer calls the control panel and, after the handshake, the control panel
immediately proceeds to the exchange of data. This simplified mode of establishing
communication is reached when the computer telephone number is not entered in the
control panel. Notification of the monitoring station will take place after communication
with the computer is over.
3) Establishing of communication from the control panel by calling the user function 0
(zero). The control panel first notifies the monitoring station that the programming has
started (when monitoring is active), then it dials the computer telephone number.
In order to reduce the cost of telephone connections, multiple suspension of the transmission
is possible. At the next connection, the control panel does not inform the monitoring station of
remote programming. Only after receiving the command to end the communication,
a message on completing the remote programming is sent to the station.
Initialization of communication can be disabled from the computer. When the communication
is suspended from the computer, the control panel is waiting for a call from the computer for
four hours even when the functions of automatically answering the computer call are
disabled. When the communication is ended with the “end” command instead of “suspend”,
the information on ending the communication is entered into the event log and sent to the
monitoring station after four hours.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info