699577
12
Zoom out
Zoom in
Previous page
1/43
Next page
10 Installer Manual SATEL
3) Zone state display LED standard. This mode is similar to the mode 2.
The difference is that in the second line the state of 12 zones of the control panel is
being monitored in the same way as it is the case in the LED keypad.
The operating mode 1 or 2 is recommended for the LCD keypad. Having selected the
mode 1, the user can temporarily switch the display between the text mode and the zone
state mode by holding down the key.
The operating mode is defined by the installer with the Status format service function
(Service Mode; LCD Keypad; Settings; Status format), available only after
activation of the control panel service mode.
The LCD keypad is fitted with a RS-232 port to enable programming the keypad settings
directly from the computer (see section: Activating selected functions).
Monitoring
The CA-10 control panel can transmit information about the system (partition) status to one
or two monitoring stations. Communication with the monitoring stations takes place
irrespective of the voice messaging and the messaging to paging systems. It has a priority
and is realized before the voice messaging. In case problems occur with getting connected to
the station, the control panel will suspend dialing the station number for 60 seconds and, if
the message is also to be transmitted by the dialer, it will make the line available to the dialer.
There are a few ways of transmitting information to the monitoring stations.
Reporting to one station.
Reporting to Station 1, and if unavailable – to Station 2 (e.g., when the station has two
telephone numbers). If this is the case, all events are reported, irrespective of which
station was reached by the control panel.
Reporting to both stations with event sorting depending on what event occurred in
the system, e.g. information on alarms to Station 1, and information on troubles to
Station 2 (this mode is useful where the station serves many subscribers and it is
necessary that the number likely to receive most vital information be busy as little as
possible). In this mode, during control panel programming, you can determine which
information is to be sent to which station.
Reporting to both stations: Station 1 first, then Station 2. This mode is reached by
assigning the same event to both stations.
In case of a system with 16 zones and 32 users, the number of messages to be sent to the
monitoring station in order to ensure an appropriate facility protection degree may be large
enough to exceed the capacity of standard transmission formats. Therefore, to increase the
control panel flexibility, the events occurring in the system have been divided into six groups:
the first one includes the zone related events (this group has the highest priority),
four groups are represented by the partition related events (the event priority depends
on the partition number, the first partition having the highest priority),
the sixth group accounts for the other system events.
Individual system identifiers are assigned to each group of events (one for each station).
In the event of stations which cannot accept several different identifiers in one
communication session, the control panel can send the events in separate sessions, in the
order resulting from the priority, grouping events with the same identifiers.
It is possible to send information on nine different zone related events and seventeen
partition related events (whereof seven events may contain the user number). The control
panel is also capable of sending twenty six other events which occurred in the system (e.g.
troubles, start of programming mode via a telephone, activation of service mode, etc.).
The event codes for both stations are the same. For a majority of events, it is possible to
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info