470265
72
Zoom out
Zoom in
Previous page
1/92
Next page
72
appears on the screen
The end of lamp life is approaching. Replace the lamp with a new one promptly.
(See page 66)
appears on the screen
The filter is out of scroll. Replace the filter cartridge with a new one promptly.
(See pages 62-63)
The image is out of focus.
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
Note: Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on Projection Lens. In such cases,
leave the projector OFF and wait until condensation evaporates.
Projecting from excessive slant angle to the screen may cause keystone distortion and
partial imperfect focus.
The image is not bright
enough.
– Check if “Contrast” or “Brightness” are adjusted properly. (See page 46)
– Check if “Image level” is selected properly. (See pages 39, 43)
– Check the Lamp control function. ( See “SETTING” section on page 50)
Check the Lamp 1/2 replace indicators. If it lights, the end of lamp life is approaching.
Replace the lamp with a new one promptly. (See page 66)
The image is darker when 1 lamp mode is selected, compared with 2 lamp mode.
Check the lamp mode at SETTING section on page 50.
The color is strange.
– Check the Input signal, color system, video system, or computer system mode.
The image is Left/Right
reversed.
– Check the Ceiling / Rear function. (See pages 41, 45)
The image is Top/Bottom
reversed.
– Check the Ceiling function. (See pages 41, 45)
The image is distorted or
runs off.
– Check “PC Adjust” menu or “ Screen” menu and adjust them.
Auto PC adjustment
function does not work.
Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p,
720p, 480i, 575i, 1035i, 1080p, or 1080i is selected or when the digital signal is input
into DVI terminal. (See page 36)
Some displays are not
seen during the operation.
– Check the Display function (see page 49).
The setting does not
remain after turning off
power.
Make sure you selected “Store after adjusting settings. Some settings cannot be
stored if not registered with “Store.
Power management
function does not work.
Power management function cannot work while “Freeze function is running or the
shutter is closed.
Image disappears
automatically.
Check the power management function in the Setting. The power management is set
to "On" at the factory.
Capture function does not
work.
– Check the connection to see if there is signal.
Some menus cannot be
selected.
– Each of the Video Input and Computer Input has a limit on selectable menus.
Appendix
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PDG-DET100L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PDG-DET100L in the language / languages: English as an attachment in your email.

The manual is 10,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PDG-DET100L

Sanyo PDG-DET100L User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info