470265
71
Zoom out
Zoom in
Previous page
1/92
Next page
71
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly
connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the projector from your computer and check your computer
monitors display. A problem may be noticed with your graphics controller rather than with the projector.
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the
projector. Turn on equipment in the order of the projector and computer.)
6. If a problem still persists, check the following solutions.
Appendix
Problem: Solutions
No power.
– Plug the power cord of the projector into the AC outlet.
Turn the MAIN ON/OFF switch to ON.
– Press the ON/STAND-BY Button to ON.
– Make sure the POWER indicator lights.
Check the indicators. If the LAMP indicator lights and the other indicators blink, the
projector cannot be turned on. (Refer to page 70.)
– Check the projection lamp. (Refer to page 66.)
PIN code dialog box
appears at start-up.
PIN code lock is being set. Enter a PIN code; the “1234” or numbers you have set (see
pages 24, 58-59)
The initial display is not
shown.
– Make sure Off ” or “Countdown Off” are not chosen at Display function.
(See “SETTING” section on page 49)
The initial display is not
same with the default
one.
– Make sure “User” or Off” are not chosen at Logo select function.
(See “SETTING” section on page 54)
When the projector is on
and you press the input
button, an icon other
than the Lamp mode icon
appears.
That is the Filter warning icon. Refer to page 61.
An icon other than Input
mode or Lamp mode icon
appears.
That is the Lamp replacement icon or the Filter warning icon. See pages 61, 66.
No image.
– Check the connection between your computer or video equipment and the projector.
See if the input signal is correctly output from your computer. Some laptop computers
may need to be changed the setting for monitor output when connected to the
projector. See your computer’s instruction manual for the setting.
– It takes about 20 seconds to display an image after turning on the projector.
– See if the selected system is corresponding with your computer or video equipment.
Select correct input source once again through menu operation (See pages 32, 42).
Make sure the temperature is not out of Operating Temperature
(41˚F–104˚F [5˚C–
40˚C]).
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PDG-DET100L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PDG-DET100L in the language / languages: English as an attachment in your email.

The manual is 10,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PDG-DET100L

Sanyo PDG-DET100L User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info