767114
18
Zoom out
Zoom in
Previous page
1/28
Next page
D. General Vehicle Installation
33 34
D-4 Knowing Your Vehicle Belts
Review your vehicle’s owner manual for vehicle seat belt use
with child restraints. This is your best source for information
concerning your vehicle.
Not all vehicle belts will work with this child restraint. This
child restraint must be tightly locked in place at all times,
during travel. You must determine if your vehicles belts are
compatible with this child restraint.
Vehicle Belts
• Automatic/Passive vehicle seat belts
You MUST have a lap belt to install any child restraint. An
automatic (passive) shoulder belt may or may not have a
separate lap belt. Consult your vehicle’s owner manual.
• Vehicle belts in center of the door
or side panel
You must move the child restraint to
another seating location. Consult your
vehicle’s owner manual.
• Vehicle belts that are in front of
the seat bight
You may need to move the child
restraint to another seating location.
Consult your vehicle’s owner manual.
Do Not Use with inflatable seat belts
You may need to move the child restraint to another seating
location or use LATCH belts only.
• ELR (Emergency Locking Retractor) vehicle belts
These lap and shoulder belts only lock
in a sudden stop or crash, and do not
properly secure a child restraint alone.
Consult your vehicle’s owner manual.
To learn if you have this type of belt,
gently pull the belt all the way out of the retractor (spool), let it
return several inches, then pull on it again. If it moves freely,
it is an ELR belt. If it is locked and will not allow any more
belt to come out, it is a switchable retractor.
ELR lap-only belts MUST NOT be used with
this child restraint.
• Switchable retractor
These belts switch from ELR to ALR (Automatic Locking
Retractor). You must have the vehicle belts in the locking
mode to use them. Follow the instructions in the
installation sections.
• ALR (Automatic Locking Retractor)
These belts lock after pulling the webbing out and letting the
belt go back into the retractor an inch or two. Follow the
instructions in the installation sections.
Vehicle Latch Plates • Check the Latch Plates
Grasp the tongue portion of
the latch plate (the part that
goes inside the buckle) and
pull straight out, inline with
the lap belt. If the latch
plate does not slide up and
down the vehicle belt, you
have a locking latch plate.
You should not need to use
a locking clip. Consult your
vehicle’s owner manual.
If the latch plate slides up and down on the belt, and you have
an ELR retractor, you MUST use a locking clip to install the
child restraint. You may not need to use the locking clip with
a switchable or ALR retractor. Consult your vehicle’s owner
manual.
Locking
Latch
Plate
Sliding
Latch
Plate
If you have an ELR lap and shoulder belt, review the “Vehicle
Latch Plate” section to see if you need a locking clip.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Safety 1st Summit 65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Safety 1st Summit 65 in the language / languages: English as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info