661029
31
Zoom out
Zoom in
Previous page
1/72
Next page
5
When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the
cutting tool is pointing in the direction away from the user, but only as far
as absolutely necessary. For as long as the equipment has not been
lowered to the ground again, both your hands must be on the top part of
the bar.
Do not start the engine when persons or animals are standing in front of
the mower.
When using equipment with a side ejector, do not start the engine when
you are standing in front of the ejector channel or other people/animals
are located in the ejection area.
Pos: 11.7.34 /Innenteil/Sicherheitsvorschriften/Handhabung/Hände oder Füße nicht in die Nähe von drehenden Teilen Mäher @ 0\mod_1115128631906_1521.docx @ 1600 @ @ 1
Never put your hands or feet near or under revolving parts. Always make
sure that your hands or feet do not get under the housing. Always
maintain a safe distance from the ejector opening.
Pos: 11.7.35 /Innenteil/Sicherheitsvorschriften/Handhabung/Netzstecker abziehen @ 40\mod_1440676308491_1521.docx @ 418681 @ @ 1
Stop the engine by releasing the motor stop bar, pull the plug, make sure
that all moving parts have come to a complete standstill:
if you intend to leave the machine;
before inspecting the connection cable;
before you inspect, clean or carry out work on the machine;
before unblocking jams or removing blockages in the ejection
channel;
if a foreign body has been encountered;
when the machine starts to vibrate strangely.
Pos: 11.7.36 /Innenteil/Sicherheitsvorschriften/Handhabung/Fremdkörper: durch Fachhändler prüfen lassen @ 0\mod_1115129695921_1521.docx @ 1597 @ @ 1
If a foreign object has been encountered or if the machine becomes blocked, e.g.
by driving onto an obstacle, a specialist dealer must check whether parts of the
machine have been damaged or deformed. Any necessary repairs must also be
carried out by an authorized specialist workshop.
Pos: 11.7.37 /Innenteil/Sicherheitsvorschriften/Handhabung/starke Vibration: durch Fachhändler überprüfen @ 24\mod_1376572097176_1521.docx @ 182608 @ @ 1
If the machine starts to vibrate unusually heavily or to make unusual noises,
please have it checked immediately by an authorised workshop.
Heavy vibrations on your hands can damage your health. Please contact an
authorised workshop immediately if heavy vibrations occur.
Pos: 11.7.38 /Innenteil/Sicherheitsvorschriften/Handhabung/Bedienungsanleitung ... Geräuschpegel ... Schwingungen ... Höchstwerte @ 28\mod_1386060456110_1521.docx @ 220094 @ @ 1
WARNING
The noise and vibration levels shown in these operating instructions are the
maximum levels for use of the machine.
The use of an unbalanced cutting element, the excessive speed of movement, or
the absence of maintenance have a significant influence on noise emissions and
vibrations. Consequently, it is necessary to take preventive steps to eliminate
possible damage due to high levels of noise and stress from vibration.
Maintain the machine well, wear ear protection devices, and take breaks while
working.
Adhere to the maintenance work listed in this operating manual and have the
equipment checked and serviced regularly by an authorised workshop.
Pos: 11.7.39 /Innenteil/Sicherheitsvorschriften/Handhabung/Motor abstellen wenn ...Elektromäher, Mulcher @ 40\mod_1440677455804_1521.docx @ 419185 @ @ 1
Switch the engine off by releasing the motor stop bar, make sure that all
moving parts have come to a complete standstill,
if you have to lift or tilt the mower e.g. for transport purposes;
when you need to transport the machine to and from the area to be
mowed
when driving off the lawn;
if you have to leave the machine for a short time;
when you wish to adjust the cutting height;
before you remove the grass collecting bag.
before you remove the mulching plug;
Pos: 11.8.1 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/1.1 Wartung und Lagerung @ 0\mod_1115184259875_1521.docx @ 1633 @ 2 @ 1
Maintenance and storage
Pos: 11.8.2 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Ungenügende Wartung ..... sicherheitsrelevanten Mängeln. @ 25\mod_1377160559113_1521.docx @ 186920 @ @ 1
Insufficient equipment maintenance will lead to safety-related faults.
Pos: 11.8.3 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Schraubverbindungen fest ... sicherer Arbeitszustand ... @ 0\mod_1115184352828_1521.docx @ 1645 @ @ 1
Ensure that all screws have been tightened securely and that the machine is in a
safe working condition.
Pos: 11.8.4 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Öffnen Auswurfklappe..Grasfangsack abnehmen, Mulcher @ 2\mod_1146561513703_1521.docx @ 12283 @ @ 1
The ejection flap must only be opened and the grass collector or mulch
stopper removed when the engine is turned off.
Pos: 11.8.5 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Steinflug, Grasfangeinrichtung prüfen Mäher @ 19\mod_1346241978491_1521.docx @ 148302 @ @ 1
Before you start mowing, always check the grass collecting equipment for
wear or loss of functionality.
Pos: 11.8.6 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/vor jedem Mähen ...Zustand ...Messers prüfen Mäher Elektromäher @ 19\mod_1346241269612_1521.docx @ 147996 @ @ 1
Before you start mowing, always check the condition and firm attachment
of the cutting blade. The blade attachment screw must always be tightened
by an authorised workshop since an insulation protection test always has
to be carried out after repairs or maintenance work on insulation parts (e.g.
blade screw) in accordance with the applicable standard DIN EN 60335. A
worn or damaged blade must always be replaced.
Pos: 11.8.7 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Auswechseln, Nachschleifen ...Auswuchten ...Messers Elektromäher @ 0\mod_1115185753187_1521.docx @ 1639 @ @ 1
Always have the replacement, sharpening or balancing of the blade carried
out by an authorised workshop, since according to the applicable standard
DIN EN 60335, an insulation test must always be carried out following repairs
or maintenance work to insulating components (e.g. blade screws).
Pos: 11.8.8 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Beschädigte Teile ersetzen @ 0\mod_1115186070093_1521.docx @ 1634 @ @ 1
For reasons of safety, always replace worn or damaged parts.
Pos: 11.8.9 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Schutzhandschuhe tragen @ 0\mod_1115186195468_1521.docx @ 1646 @ @ 1
Protective gloves must be worn at all times during maintenance and
cleaning work.
Pos: 11.8.10 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Netzstecker abziehen @ 26\mod_1377184199602_1521.docx @ 192863 @ @ 1
Maintenance and cleaning work may only be carried out with the motor
switched off and mains plug disconnected. When servicing the cutter
blades note that they can be moved even when the voltage source is
switched off. Regular maintenance is essential for safety and top
performance.
Pos: 11.8.11 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Gerät nicht ...fließendes Wasser @ 0\mod_1125473581015_1521.docx @ 1640 @ @ 1
Do not clean the machine with running water or pressure cleaners. This
could damage the electrical system.
Pos: 11.8.12 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Nur Originalersatzteile verwenden SABO+JD @ 26\mod_1377168488208_1521.docx @ 187532 @ @ 1
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
Pos: 11.8.13 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Schweiz @ 0\mod_1125474167283_1521.docx @ 1647 @ @ 1
Notes for Switzerland:
Electric appliances must only be operated if a residual current operated device
with a maximum breaking current of 30 mA is also integrated into the circuit.
Pos: 11.8.14 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Österreich @ 0\mod_1125474640679_1521.docx @ 1644 @ @ 1
Notes for Austria:
The socket coupler of the connecting cable must be splashproof.
Pos: 12.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 12.2 /Innenteil/Beschreibung der Bauteile/1 BESCHREIBUNG DER BAUTEILE @ 0\mod_1115187892468_1521.docx @ 1664 @ 1 @ 1
7 DESCRIPTION OF COMPONENTS
Pos: 12.3 /Innenteil/Beschreibung der Bauteile/Bild 36-EL @ 29\mod_1392382458149_0.docx @ 226059 @ @ 1
Pos: 12.4 /Innenteil/Beschreibung der Bauteile/Beschreibung der Bauteile 36-EL Text @ 22\mod_1361356926434_1521.docx @ 169633 @ @ 1
1 Actuating grip for motor (safety grip)
2 Cable connection plug
3 Ejection flap
4 Electric motor
5 Handle for adjusting the height
6 Motor bracket
7 Cutting height indicator
8 Carrying handle front
9 Strain relief device for electric cable
10 Cable guide
11 Casing on the upper part of the bar
12 Locking button (red)
Pos: 13.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sabo 36-EL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sabo 36-EL in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info