733430
11
Zoom out
Zoom in
Previous page
1/44
Next page
9
Make sure the air filter is clean.
Check both the engine lubricant level and
the fuel tank level. Refill as needed.
Inspect the work area for hazards.
If there is excessive noise or vibration, stop
the product immediately.
NOZZLE MAINTENANCE
Excessive pump pressure (a pulsing sensation
felt while squeezing the trigger) may be the
result of a clogged or dirty nozzle.
Turn off the high pressure cleaner and shut
off the water supply. Squeeze trigger to
release water pressure.
Remove the nozzle from the spray wand.
NOTE: Never point the spray wand to
yourself and others.
Using a straightened paper clip or nozzle
cleaning tool (not provided), free any
foreign materials clogging or restricting the
nozzle.
Using a garden hose, flush debris out of the
nozzle by back flushing (running the water
through the nozzle backwards or from the
outside to the inside).
Reconnect the nozzle to the spray wand.
Turn on the water supply and start the
engine.
CLEANING THE AIR FILTER
See pages 33-34.
A dirty air lter will cause starting difculty,
loss of performance, and shorten the life span
of the engine. Check the air lter monthly. For
best performance, replace the air lter at least
once a year.
REPLACING THE SPARK PLUG
See page 35.
Clean the area around the base of the
spark plug before removing to keep dirt
and debris out of the engine. Remove
spark plug.
Clean the carbon deposits on the spark
plug electrode using a plug cleaner or wire
brush. Replace the plug if worn. To replace
the spark plug, see page 34. Use spark
plug model BPR7HS (NGK) or equivalent.
Check electrode gap. The gap should be
0.7- 0.8 mm (0.03 in.). Adjust the gap, if
necessary, by carefully bending the ground
electrode.
Reinstall spark plug and tighten securely.
CHANGING THE ENGINE LUBRICANT
See page 36.
NOTE: Drain the lubricant while the engine
is still warm but not hot. Warm lubricant will
drain quickly and more completely.
NOTE: Consult hazardous waste management
guidelines in your area for the proper way of
used lubricant disposal.
PUMP LUBRICATION
The pump used in the high pressure cleaner
was lubricated with a sufcient amount of high
grade lubricant for the life of the product under
normal operating conditions. Therefore, no
further lubrication is required.
SYMBOLS ON THE PRODUCT
Safety alert
Read and understand
all instructions before
operating the product, follow
all warnings and safety
instructions.
Wear full eye and ear
protection.
To reduce the risk of injury
from kickback, hold the spray
wand securely with both
hands when the product is on.
Never point the spray wand to
people, animals, the machine
body, power supply, or any
electric appliances.
The product is not suitable
for connection to the drinking
water mains.
Burst hazard
To reduce the risk of injury
from high-pressure injection,
do not direct spray at people
or animals.
Failure to use in dry conditions
and to observe safe practices
can result in electric shock.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi RPW3200Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi RPW3200Y in the language / languages: English as an attachment in your email.

The manual is 10,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info