733431

Ryobi RPW150-G Manual

5
Zoom out
Zoom in
Previous page
1/28
Next page
3
■ Stop the product, disconnect from the power supply,
and allow the product to cool down. Disconnect
the product from the water supply before storing or
transporting. Never place the product in any position
other than upright.
■ Remove water from all hoses and the pump, and empty
the detergent tank before storing the product.
■ Clean all foreign materials from the product. Store it
in a cool, frost-free, dry, and well-ventilated place that
is inaccessible to children. Keep away from corrosive
agents such as garden chemicals and de-icing salts.
Do not store outdoors.
■ For transportation in a vehicle, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, contribute to poor performance,
and may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualied service
technician. For service, bring the product to an
authorised service centre. When servicing, use only
original replacement parts.
■ Stop the product, disconnect from the power supply,
and allow the product to cool down. Disconnect the
product from the water supply before:
● cleaning the product
● maintaining the product
● replacing spare parts
■ You may make adjustments or repairs described in
this manual. For other repairs, contact an authorised
service centre.
■ Regularly inspect and maintain the high pressure
cleaner for safe operation. Ryobi recommends
inspecting the product every 6 months.
■ Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■ Injury caused by the high-pressure jet
– Avoid pointing the high-pressure jet to people,
animals, and to yourself.
■ Injury caused by kickback
– Always hold the handle or the trigger wand firmly
with your two hands.
■ Injury caused by inhalation of aerosols
– Wear appropriate respiratory mask.
■ Injury caused by exposure to noise
– Wear ear protection.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome.
Symptoms may include tingling, numbness, and blanching
of the ngers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking, and work practices are all thought to contribute to
the development of these symptoms. There are measures
that can be taken by the operator to possibly reduce the
effects of vibration:
■ Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
SYMBOLS ON THE PRODUCT
Warning
Class II tool, double insulation
To reduce the risk of injury, user must
read and understand operator’s manual
before using this product.
Wear eye and hearing protection.
Remove plug from the mains immediately
if cable is damaged or cut.
Electrical shock hazard
… 5 …


Need help? Post your question in this forum.

Forumrules
1

Forum

ryobi-rpw150-g

Reset search

  • My Ryobi RPW150-G will run at full pressure for about 10 seconds then stop, I release the trigger and engage again and the same thing happens.
    The in line filter is clean and there is ample water pressure.
    I have used my sons Ryobi cleaner and it works fine.
    Any ideas
    Brian Submitted on 21-11-2022 at 04:16

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi RPW150-G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi RPW150-G in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info