Manual Rupes S145 (page 10 of 112) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

489906

Zoom out

Zoom in

1/112

MACHINE USE

The machine can operates in manual or automatic mode: to select the mode, turn the

switch (12) to the right (automaxtic mode) or to the left (manual mode) (pic. 23). The

green indicator (13) turns on when the vacuum motor starts.

Using the machine in automatic mode (A)

Automatic operations means that the vacuum starts when an electrical or pneumatic

tool is turned on.

The vacuum will automatically turn off eight seconds after the tool is turned off.

Using the machine in manual mode (M)

Manual operations means that the vacuum runs continuously.

Power on the front panel outlet socket is permanently active during manual running.

Adjusting the vacuum level

The vacuum level can be adjusted in both operating modes by turning the knob (12)

towards the "min" position until the desired power is reached.

Automatic cleaning of the filters (VERSION “E”)

The machine has a timed filter cleaning system that maintains the vacuum strength

constant.

It is also possible to perform a complete cleaning cycle as follows (pic. 19):

- switch the machine off;

- cap the vacuum sleeve;

- restart the machine keeping the sleeve capped for 15 seconds.

Suction hose setting (VERSION “M”)

For operators safety the appliance for M class dust are provided with an indicator which

operates in case of the air velocity throught the hose falling below 20 m/sec.

Check the hose diameter and set the correct value on the front panel throttle (32) (pic.

23).

To be used with genuine RUPES hoses.

Acoustic alarm operates (VERSION “M”)

In case of acoustic alarm on locate the causes (C.) and redress (R.) it with the action re-

commended in the following procedure:

C: Power set-up too low;

R: Increase the suction power;

C: The hose diameter doesn’t match with the hose set-up on the front panel;

R: Set the hose diameter knob (32) on the right diameter;

C: Clogged or bended hose;

R: Check and set straight the hose;

C: Dust bag full;

R: See dust bag “REPLACEMENT SECTION”;

C: Clogged filers;

R: See filter cartridges “REPLACEMENT SECTION”.

After operating in hazardous dust contaminated environment all appliance

parts must be considered as contaminated; before handling the appliance out

the1contaminated area or servicing it, remove all the dust from it with vacuum

or cloth, seal the dust container with the rubber cap (33), and store hose and

accessories in a sealed bag (VERSION “M”).

Wet vacuum (VERSION “E”)

Before vacuuming liquids, remove the dust bag(paper or plastic) and replace the paper

filters cartridges with polyester ones. The filters should be damp after vacuuming.

Do not operate with dry dust with wet filters!

Liquid level indicator (VERSION “E”)

The vacuum motor stops and the liquid level indicator (14) turnes on when the the liquid

sensor (24) detects the bin (25) full. To reset empty the bin (25).

MAINTENANCE

A yearly technical check on parts and filtering system by an authorized ser-

vice centre is required.

Service indicator (15)

The indicator turns on for scheduled service to keep the machine working conditions.

When warning light is on contact an authorized service centre to check and service the

appliance and reset the warning light.

The prolongated use of the vacuum cleaner with the warning light on can cause more

maintenance operation.

Ordinary check operations

For user servicing, the appliance must be dismantled, cleaned and serviced,

as far as it is reasonably practicable, without causing risk to the maintenance

staff and others. Suitable precautions include, decontamination before di-

smantling, provision for local filtered exhaust ventilation where the appliance

is dismantled (according to local regulations), cleaning of the maintenance

area and suitable personal protection.

- check the vacuum hose conditions;

- VERSION "E": clean the liquid level sensor (24);

- check the power cord, plug and outlet socket conditions: in case contact an authorized service

centre for replacement;

- check the dust bag: do not exceed recommended weight and capacity! In case of laceration or

perforation of the dust bag check the filter cartridge and eventually ask for replacement to an

authorized service centre;

- check filter cartridges condition (23). In case of lacerations or perforations contact an authjo-

rized service centre for replacement.

Do not use the appliance without the full filter set fitted!

Bag replacement

Do not spread dust during dust bag replacement!

- wear an adeguate dust mask;

- detach the vacuum head pushing the side hooks (11) and remove the vacuum head (1) (pic.

7-8).

Paper bag (cod. 042.1108/5):

- VERSION “M”: seal the dust container with the appropriate cap (33);

- remove the full bag closing the nozzle with the cap provided (pic. 12 and 13);

- put the new bag inserting the nozzle as illustrated (pic. 14).

Plastic bag:

- remove the full plastic bag (pic. 9);

- place the new bag, verifying that the nozzle is positioned on the inlet (pic. 10);

- turn the bag edge as shown (pic. 11); make sure to keep the compensation holes inside the

bin.

Only use genuine RUPES dust bags.

Spare bags shozuld be kept in dry places!

Follow local legal regulations for disposal.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rupes S145 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rupes S145 Manual

Product: