489839

Rupes BH252R Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
12 Latch for mains cable module
13 Adapter for screwdriver bits/drill chuck
Accessories illustrated or described are not
always included as standard delivery items.
3. TECHNICAL DATA
Input power 700 Watt
No-load speed 1st gear 0-1170 rpm.
No-load impact number max 5270 rpm.
Impact energy 2,5 Joule
Recommended drilling area Hammer
drilling up to Ø 4-16 mm
Hammer drilling in concrete up to Ø 24 mm
Drilling in steel up to Ø 13 mm
Drilling in wood up to Ø 30 mm
Collet Ø 43 mm
Weight 2,6 Kg
4. NOISE/VIBRATION INFORMATION
Measured values determined according to EN 60
745.
Typically the A-weighted noise levels of the
machine are: sound pressure level 88 dB (A);
sound power level 99 dB (A). Measurement
uncertainty K = 3 dB.
Wear hearing protection!
The typically weighted acceleration is 7,6 m/s
2
.
5. MOUNTING THE AUXILIARY HANDLE AND
THE MAINS CABLE MODULE
Before any work on the machine itself, pull
the mains plug!
Operate the machine only with the auxiliary han-
dle 11. Place the auxiliary handle on the clamping
collar and tighten with the clamping screw.
Connect the mains cable module to the handle.
The plug must latch.
Use the mains cable module provided only
for Rupes Electro-Tools. Do not attempt to
operate other machines with the module.
Use only an original Rupes mains cable module
that is at least of heavy rubber sheathed cable.
6. PUTTING INTO OPERATION
Check before putting into operation that the
mains voltage agrees with the voltage specified
on the nameplate of the machine.
SWITCHING ON/OFF
Press or release the On/Of
f switch 8.
The on/off switch can be locked on with the loc-
king button 7. To release, briefly press and relea-
se the on/ off switch 8.
ROTATION STOP
With the rotation stop switch 4, two settings can
be selected.
1 = Drilling/hammer drilling, mixing work
= No rotation: Light chiselling work.
The switch-over can best be performed at a stan-
dstill.
Only after the on/off switch 8 is actuated and the
machine starts does the gear box shift to the
selected mode.
DRILLING - IMPACT DRILLING
For drilling, place the selector 9 in the
position.
For impact drilling, set to
The switch-over can best be performed at a stan-
dstill. Only after the On/Off switch 8 is actuated
and the machine starts does the gear box shift to
the selected mode.
Note: Left rotation when impact drilling damages
the drill. Switch off the impact mechanism for dia-
mond crown drilling or for mixing work.
For chiselling work, set the selector 4 to the
position.
When hammer drilling, use exclusively drills
with hard metal inserts and SDS-plus shafts.
The use of commercially available masonry drills
with cylindrical shafts by means of the adapter 13
and the normal drill chuck in conjunction with the
pneumatic impact mechanism is not possible.
SPEED CONTROL
With the On/Off switch 8, the
speed can be continuously
varied. With light pressure on
the on/off switch 8, the machi-
ne begins to rotate slowly; with
increased pressure, the speed increases.
ROTATIONAL DIRECTION SWITCHING
Operate the rotational direction
switch 6 only when the machi-
ne is at a standstill!
Take hold of the rotational
direction switch 6 on both
sides.
Right rotation: Set the rotational direction switch
6 to “R”.
Left rotation: Set the rotational direction switch
6 to “L”.
Important! Press the rotational direction switch 6
in each case to the stop on the housing, i. e. until
it can be felt to engage.
If the rotational direction switch 6 is set between
the positions “R” and “L”, the machine cannot be
switched on.
6
Fet
t
3
Fet
t
3
Fet
t
3
Fet
t
3
Fet
t
Fet
t
librettoBH252R 21-08-2007 9:30 Pagina 6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes BH252R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes BH252R in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info