6
EN
4. BEFORE USING FOR THE
FIRST TIME
Before using your espresso machine for the
first time, clean all the accessories in soapy
water and dry them.
Rinse them as follows:
Open the lid (a) and remove the water tank
using the handle (fig. 1).
Fill the tank (b) with cold water and place it
firmly on the machine, making sure it is firmly
in place, and close the lid (fig. 2 et 3).
nsert and turn the filter holder to the right
(fig 7).
Place a container of sufficient volume under
the filter holder.
Turn the appliance on (fig. 4).
The "On/Off" light stops (g) stops flashing and
turns on.
Without waiting, turn the Coffee function
selector (h) to the position (h2) and let all
the water in the tank drain out (Fig. 5). During
this first use, the system must fill up and the
water does not flow immediately.
If necessary, to empty the water from the
container, you can interrupt the flow by turning
the coffee function selector switch (h) to the
position (h1).
5. MAKING AN ESPRESSO
WITH ESPRESSO GROUND COFFEE:
- Fill the tank with cold water and place it firmly
on the machine, making sure it is firmly in
place, (fig. 1, 2 and 3).
- Place the filter (c.1) for 1 cup or the filter (c.2)
for 2 cups in the filter holder (j) (fig. 6).
- using the measuring spoon (d), fill the filter
with ground coffee.
(1 dose = 1 cup, 2 doses = 2 cups) in the filter.
(fig 8, 9)
- Remove the coffee which remains around the
filter.
- Insert and turn the filter holder to the right
(fig 7).
- Place one or two espresso cups under the
filter holder.
As soon as the device reaches the required
temperature, the coffee light (h3) stops
flashing.
- Turn the coffee function selector switch (h) to
the position (h2).
- When the cups are filled to your liking, turn
the switch to the logo position (h1).
- Remove the filter holder by turning it to the
left .
- To eject the spent coffee, turn the filter holder
over, holding the filter by the tab so that the
spent coffee does not fall out (fig 11).
For the best results, we recommend that you
preheat the accessories (filter holder, filter and
cups) following the steps above without using
ground coffee.
WITH SOFT PODS:
Besides coffee, this machine can also work
with espresso ground coffee pods.
There are two types of espresso pods
commercially available:
- Soft pods (71mm) for filter (C1).
- Place the espresso pod in the filter (c1).
Be sure to place all the paper inside the filter
holder, to avoid leaks and get a good result in
the cup.
- Insert and turn the filter holder to the right
(fig.7).
- Then follow the procedure for preparing an
espresso with espresso ground coffee.
6. STEAM FUNCTION AND
MAKING A CAPPUCCINO
You can use the steam nozzle to froth milk.
Foamy milk is obtained by placing a container
of very fresh, cold milk under the steam nozzle.
It can then be added to an espresso to make a
cappuccino.
To avoid the formation of excessive pressure
inside the filter, you should remove the filter
holder before using steam.
SYSTEMATIC PURGE OF THE STEAM
CIRCUIT:
Each time before you make frothy milk, you
must purge the steam circuit:
- Place an empty container under the steam
nozzle (k).
- Turn the Steam function selector switch (i) to
the position (i2) (fig. 12). The Steam light
(i4) comes on.
- Turn the Steam function selector switch (i) to
the position (i3) (fig. 13) in order to purge
the circuit.
- When all the water inside the circuit has been
emitted, turn the Steam function selector
switch (i) back to the to the position (i2).
(fig. 12) (i2).
Warning! Do not remove the Filter holder
when the Coffee function selector switch (h)
is in the position (h2), and the coffee is
flowing.
