581051
12
Zoom out
Zoom in
Previous page
1/16
Next page
12
RC-1570 Stereo Control Amplifier
Bluetooth Connection
Insert the supplied Bluetooth Dongle into the front USB of the RC-1570 for
wireless streaming via Bluetooth, from your device (i.e. mobile phones).
From your mobile device, look for „Rotel Bluetooth‰ and connect to it.
Connection is normally automatic, but if prompted for a password, please
press „0000‰ then enter on your device.
NOTE: Not all Bluetooth dongles will operate with RC-1570. Please use
the one supplied.
Audio Controls
Volume Control
4
B
Turn the controls clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or - key
to turn the volume up or down. Press the MUTE B key to completely mute
the volume.
Balance Control
8
C
The Balance Control adjusts the left-to-right balance of the sound output.
The factory default is the center position or „0‰. To change the balance
from the front panel, press the MENU
8
key to toggle the front display to
BALANCE SETTING mode. Then press the - or + keys on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: These settings are saved permanently including after powering off
the RC-1570.
To make temporary changes not saved after power off, from the remote
press the BAL C key to access the BALANCE SETTING menu, then press
the LEFT or RIGHT E key to adjust. When finished, press the EXIT F key
to exit the menu.
Tone Control Bypass
8
K
Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show
TONE BYPASS. To turn on the tone control from the front panel, press the
MENU
8
key to toggle to the Bypass control then press the LEFT or RIGHT
keys to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off the
RC-1570.
To temporarily changes the Tone Control Bypass, press the BYPASS K key
on the remote control to toggle the Bypass mode enabled and disabled.
Bass and Treble Controls
8
C
Set the Bass or Treble controls from the front panel by pressing the MENU
8
key to toggle to either the Bass or Treble Setting menu. Then press the - or +
key to adjust the value. The Bass and Treble values range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RC-1570.
To temporarily change the Bass and Treble settings from the remote control,
press the Bass or Treble key C, then press the LEFT or RIGHT E keys on
the remote to adjust the value.
A properly setup high-performance audio system produces the most natural
sound with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load
on the amplifier and speakers.
NOTE: Setting the Bass and Treble controls do not automatically turn
on the tone control. To turn on tone control, refer to previous section
Tone Control Bypass.
Dim Control
8
L
To change the brightness of the front display, press the MENU8 button to
toggle to the Display Settings. Then press the - or + keys on the front panel
to change the display brightness.
NOTE: This setting is saved permanently including after powering off the
RC-1570.
To temporarily change the display brightness, press the DIML key on the
remote.
NOTE: Tone Bypass, Bass, Treble, Balance and dimmer settings are only
saved permanently from within the Menu. Adjustments made using the
CKL buttons are temporary only and not saved after power off.
Function Control
7
J
The Function control selects the input signal source. From the front panel or
remote press the corresponding input key to select the source to listen to.
NOTE: Pressing the Aux, Opt and Coax keys on the front panel will toggle
between input 1 and input 2.
Rotel Link
0
This 3.5 mm stereo mini-jack (labeled ROTEL LINK IN) can optionally attach
to Rotel network enabled products with ROTEL LINK OUT connections. This
allows the attached Rotel products to communicate with each other and
be controlled via the Rotel Remote App (available for download on the
iTunes
®
store).
EXT REM IN Jack
-
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when
the unit is installed in a cabinet and the front-panel sensor is blocked. Consult
your authorized Rotel dealer for information on these external repeaters and
the proper wiring of a jack to fit the mini-jack receptacle.
Computer I/O Connector
=
The RC-1570 can be controlled via RS232 for integration with automation
systems. The COMPUTER I/O input accepts a standard straight DB-9 Male-
to-Female cable.
For additional information on the connections, software, and operating codes
for computer control of the RC-1570, contact your authorized Rotel dealer.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RC-1570B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RC-1570B in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info