581051

Rotel RC-1570B Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
11
standby mode, the trigger signal is disabled, so the components controlled
by it will be turned off.
NOTE: If you are using other units in the series with Rotel link, please
use the Rotel Link connection to turn the units on or off. Do not connect
both the Rotel Link and 12V trigger cables. The 12V triggerÊs power
on or off features will override the Rotel Link features.
Input Signal Connections
See Figure 3
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.
Phono Input
q
and Ground Connection (GND)
9
See Figure 3
Plug the cable from the turntable into the appropriate left and right phono
inputs. If the turntable has a „ground‰ wire, connect it to the screw terminal
to the left of the Phono inputs. This will help prevent hum and noise.
Line Level Inputs
w
See Figure 3
The CD, Tuner, and Aux inputs of the amplifier are analog „line level‰ inputs.
These inputs are for connecting components such as CD players or other
audio playback devices with an analog audio output.
The left and right channels are clearly labeled and should be connected to
the corresponding channels of the source component. The Left connectors
are white, the Right connectors are red. Use high quality RCA cables for
connecting input source components to the RC-1570. Ask your authorized
Rotel dealer for advice about cables.
Balanced (XLR) Inputs
t
See Figure 4
A pair of balanced XLR inputs accept audio signals from CD player, Blu-ray
player or other source components with XLR outputs.
NOTE: You should choose only one method of analog connection from
a source component to RC-1570. Do not connect both the RCA and
XLR outputs of a source component to the RC-1570 at the same time.
Digital Inputs
y
See Figure 5
There are two sets of digital inputs labeled COAXIAL 1 and 2, OPTICAL
1 and 2. Connect the COAXIAL or OPTICAL PCM outputs of your source
component into these sockets. The digital signals will be decoded and
played by the RC-1570. The unit is capable of decoding PCM signals up
to 24 bit, 192kHZ.
Output Connections
Preamp Output e
See Figure 3
The RC-1570 RCA-type output connectors are compatible with most power
amplifiers. As always, select high quality audio interconnect cables. Connect
the left and right channel outputs of the RC-1570 to the corresponding inputs
on the preamplifier or other component.
NOTE: There are two sets of RCA outputs on the RC-1570. The second
set of outputs may be used in custom system configurations to drive
a second power amplifier or to supply a signal to a special signal
processor.
Balanced (XLR) Preamp Output r
See Figure 4
A pair of XLR balanced connectors supplies an analog output signal from
the RC-1570 to a power amplifier with XLR balanced input connectors.
NOTE: Do not connect both the RCA and XLR to the same amplifier
at the same time.
Headphone Output
6
The headphone output allows you to connect headphones for private listening.
This output accepts a standard 3.5mm (1/8‰) mini stereo headphone
connector. Plugging in a set of headphones does not cut off the signal to the
preamp outputs. In most instances you should turn off the power amplifier
when listening to headphones.
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.
Remote Sensor
2
This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.
Display
3
The front panel display shows the source selected, volume level and tone
settings.
Front USB Input
5
See Figure 6
The front USB input can be connected to an iPod, iPhone, USB flash memory
or the Bluetooth dongle (supplied) for wireless streaming. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RC-1570B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RC-1570B in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info