714264
30
Zoom out
Zoom in
Previous page
1/32
Next page
30
The appliance does not
stop when the seed
container is empty.
The appliance was not adapted to your local electricity supply.
- Start the voltage adaptation programme (refer to point “Voltage adaption –
Activating the auto cut-off function” on page 31)
The appliance generates
loud noise during
operation
Check whether the appliance is correctly assembled.
There are possibly some foreign matters in the material to be pressed.
- Remove the foreign matters and restart the appliance.
(see section on “Clearing a screw conveyor blockage”).
It depends on the material to be pressed, to which extend the motor and/
or the screw conveyor is under stress. This can result in loud operating noise.
- Material is too moist. Dry it again in the oven.
- The material is too large - Crush again.
Due to the cleaning with washing-up liquid, the sealing and the casing are
completely fat free; this may cause a loud friction noise
- Apply a drop of oil on the sealing.
In case the screw conveyor casing has a blockage inside and you try to
release the blockage by using the reverse function, loud creaking noises
might be the result. Do not worry – this is harmless.
- Go on as prescribed in section “Clearing a screw conveyor blockage”.
No yield or unsatisfying
results
Check whether you use the correct screw conveyor.
- Exchange the screw conveyor if necessary.
• Check whether the screw conveyor or the screw conveyor casing is blocked.
- Detach both parts and clean them.
(see section on “Clearing a screw conveyor blockage”).
Check whether the screw conveyor is jammed by e.g. material which is too
moist.
- Detach the screw conveyor and clean it.
- Dry the material to be pressed in the oven.
(see section on “Clearing a screw conveyor blockage”).
The material to be pressed contains not enough oil.
- Use seeds/ nuts with a higher oil content.
Seed container cannot
be attached
Check whether the locking mechanism is slid to the stop on the left-hand
side, i.e. to the closed padlock symbol.
- Move the screw conveyor casing to and fro to lock it correctly.
Screw conveyor casing
cannot be disassembled
easily.
Foreign matters block the screw conveyor.
- Remove the foreign matters.
(see section on “Clearing a screw conveyor blockage”).
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rommelsbacher OP700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rommelsbacher OP700 in the language / languages: English, German as an attachment in your email.

The manual is 2,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info