714262

Rommelsbacher MD1000 Manual

50
Zoom out
Zoom in
Previous page
1/60
Next page
50
• Cleaning of the valve for lid locking
• Take off the small transparent seal and remove the valve pin from the casing (tip: keep your finger on
the right side of the lid on the opening for the valve so that the valve pin does not fall out). Clean the
valve pin and the seal in hot water with some mild detergents. Then thoroughly dry the parts.
• For reassembly, push the valve pin into the intended recess in the lid and hold it with a finger, insert
the seal from the other side. Pay attention to the correct fit of the seal!
• Clean the gasket ring and the lid in hot water with some mild detergent and then thoroughly dry them.
• Clean all other accessory parts also in hot water with some mild detergent.
• Use a conventional household cleaning brush with soft bristles for cleaning coarse soiling.
• Subsequently reassemble the valves according to the instructions in this manual.
• Before reassembly and before being used again, all accessory parts must be completely dry.
• Do not use any abrasives or solvents!
• Never use a steam cleaner to clean the appliance!
If an error occurs, please check the following table to see if you can fix the error by yourself. If this is not
possible, please contact your service point. Our competent contact persons will be happy to help you -
Thank you very much.
IMPORTANT: Always disconnect the unit from the power supply, release any steam pressure and allow
the appliance to cool down before searching for the cause of an error or rectifying it!
Error Cause and Elimination
Appliance without
function
LEDs do not light up
• Check whether the power cord is connected properly to the appliance and
to the power socket.
• Check with another appliance, whether the power socket has a function.
• Check whether the appliance has been assembled correctly.
The prepared dishes are
only half-done
• The filling quantity is too high, please reduce the filling quantity.
• The ratio between volume of ingredients and water is not correct, please
adjust if necessary.
• The cooking pot does not rest correctly on the heating plate, check cooking
pot whether the bottom has been deformed, if necessary replace the pot.
• There is not enough steam pressure, check gasket ring for any damages.
• The cooking time is too short, if necessary increase cooking time.
Trouble shooting
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rommelsbacher MD1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rommelsbacher MD1000 in the language / languages: English, German as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info