647744

Roland XP-30 Manual

74
Zoom out
Zoom in
Previous page
1/216
Next page
74
Chapter 3. Creating Your Own Sounds
Start (Portamento Start Pitch)
Portamento will begin anew if you press another key during
a pitch movement. This setting specifies how the new
portamento will start.
PITCH: Pitch will begin changing when the new key is
pressed.
fig.3-30.e
NOTE: Pitch will begin changing from the destination of the
current movement.
fig.3-31.e
RxSWITCH (Receive Switch)
These parameters determine how Volume/Pan/Pitch Bend
MIDI messages will be received by each Tone.
* In general, Volume messages control the volume, Pan messages
control the stereo location, and Pitch Bend messages control the
pitch of. However the XP-30 allows you to use these MIDI
messages to control other parameters that you specify. Thus, if
you are using a message to control another (i.e., a non-standard)
parameter, you should turn off reception for that MIDI message.
If reception is turned on, that MIDI message will control its
standard function in addition to the special assignment you
have made.
Volume (Receive Volume Switch)
If you want Volume messages to be received, turn this
parameter ON. If not, turn it OFF.
Pan (Receive Pan Control Switch)
Specify how Pan messages will be received.
OFF: Not received.
CONT: Whenever a Pan message is received, it will
immediately change the stereo location of the
sound.
KEY-ON: The stereo location of the sound will be changed
when the next note is played. If a Pan message is
received while a note is sounding, the current
stereo location will not change until the next note.
In this case, the stereo location will change only
for the note played later, and the currently
sounding note will not move.
Pitch Bend (Receive Pitch Bend Switch)
If you want Pitch Bend messages to be received, turn this
parameter ON. If not, turn it OFF.
DAMPER
Specify how Hold 1 (sustain pedal) messages will be received
by each Tone.
Hold-1 RxSwitch (Receive Hold 1 Switch)
If you want Hold 1 messages to be received, turn this
parameter ON. If not, turn it OFF.
Redamper (Redamper Switch)
If a Hold 1 message is received during the time between a
note-off (when you release the key) until when the sound
disappears, the currently sounding sounds will be sustained
if this Redamper setting is ON. If you use this function, you
must also turn on the Receive Hold 1 switch.
PEAK & HOLD
Hold messages (Hold 1, Hold 2, Sostenuto, Soft) are used to
sustain the sound. The XP-30 allows you to use these Hold
messages to hold the values of specific parameters.
* If you use this function, you must also turn on the Receive Hold
1 switch for the Patch (previous screen).
* If you select HOLD for the following parameters, you must also
set the Hold parameter (SYSTEM/CONTROL/CONTROL
SOURCE) to the type of Hold message being controlled.
* If you select PEAK for the following parameters, you must also
set the Peak parameter (SYSTEM/CONTROL/CONTROL
SOURCE) to the type of Hold message being controlled.
C5
D4
C4
press D4 key
Pitch
Time
press C4 key
press C5 key
C5
D4
C4
press D4 key
Pitch
Time
press C4 key
press C5 key
… 74 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland XP-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland XP-30 in the language / languages: English as an attachment in your email.

The manual is 5,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info