647744
72
Zoom out
Zoom in
Previous page
1/216
Next page
72
Chapter 3. Creating Your Own Sounds
PATCH EFX OUT (Patch EFX Output)
These parameters specify the output for the Tone for which
EFX was selected in Output Assign.
* For Tones which have an Output Assign setting of MIX, the
settings of this display will be ignored.
Mix Out (EFX Output Level)
Adjust the volume level of the original sound and the Multi-
Effects sound.
Chorus (Chorus Send Level)
Adjust the amount of Chorus for the sound that passes
through Multi-Effects.
Reverb (Reverb Send Level)
Adjust the amount of Reverb for the sound that passes
through Multi-Effects.
PATCH EFX CTRL (Patch EFX Control)
Use this setting when you wish to use a specific controller to
control an EFX parameter. The EFX parameters available for
control will depend on the selected EFX type. For details
refer to Multi-Effects Types (EFX Parameter) (p. 93). The
upper line of the display will show the EFX parameters that
can be controlled. For each EFX parameter, you can specify
the EFX Control Source and the EFX Control Depth.
EFX Control Source 1, 2
The following MIDI controllers can be used. If you wish to
use a controller that will apply to all Patches, or a controller
that cannot be directly specified here, select SYS-CTRL1 or
SYS-CTRL2, and then select the controller using the Control
1/2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN).
OFF: controller not used
SYS-CTRL1: System controller (control 1)
SYS-CTRL2: System controller (control 2)
MODULATION: Modulation (MIDI controller number 1)
BREATH: Breath (MIDI controller number 2)
FOOT: Foot (MIDI controller number 4)
VOLUME: Volume (MIDI controller number 7)
PAN: Pan (MIDI controller number 10)
EXPRESSION: Expression (MIDI controller number 11)
BENDER: Pitch bend
AFTERTOUCH: Aftertouch
EFX Control Depth 1, 2
Adjust the amount of change that will occur in response to
controller movements. Higher settings will result in greater
change. Negative (-) settings will reverse the direction of
change.
PATCH CHORUS
These parameters control the Chorus effect of the Patch.
Rate (Chorus Rate)
Adjust the speed of modulation for the Chorus effect.
Depth (Chorus Depth)
Adjust the depth of modulation for the Chorus effect.
Delay (Chorus Pre Delay)
Adjust the time delay after the original sound begins until
the Chorus effect begins to apply. Higher settings result in a
more spacious effect.
Fbk (Chorus Feedback Level)
Adjust the amount of sound from the Chorus output that is
returned (fed back) to the Chorus. Higher settings result in a
more intense effect.
Level (Chorus Level)
Adjust the volume of the Chorus effect.
Out (Chorus Output Assign)
Select the way in which the Chorus and Reverb are
connected.
MIX: The Chorus sound and the Reverb sound are mixed.
fig.3-27.e
REV:Apply reverb to the chorus sound.
fig.3-28.e
M+R: Mix the chorus sound to which reverb is not applied
and the chorus sound to which reverb is applied.
fig.3-29.e
OUTPUT
Reverb
Chorus input
Chorus
Reverb input
OUTPUT
Reverb
input
Chorus
input
Chorus Reverb
OUTPUT
Reverb
input
Chorus
input
Chorus
Reverb
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland XP-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland XP-30 in the language / languages: English as an attachment in your email.

The manual is 5,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info