527390

Roland BK-7M BACKING MODULE Manual

111
Zoom out
Zoom in
Previous page
1/128
Next page
MFX types and parameters
Backing Module BK-7m
r
111
28. OD‰ Flanger
This effect connects an Overdrive and a Flanger in series.
●
Overdrive Drive (0~127)—Degree of distortion. Also changes
the volume.
●
Overdrive Panpot (L64~0~63R)—Stereo location of the over-
drive sound.
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Flanger Depth (0~127)—Modulation intensity.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Level (0~127)—Output level.
29. OD‰ Delay
This effect connects an overdrive and a delay in series.
●
Overdrive Drive (0~127)—Degree of distortion. Also changes
the volume.
●
Overdrive Panpot (L64~0~63R)—Stereo location of the over-
drive sound.
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
30. DST‰ Chorus
This effect connects distortion and a chorus in series.
●
Distortion Drive (0~127)—Degree of distortion. Also changes
the volume.
●
Distortion Panpot (L64~0~63R)—Stereo location of the distor-
tion sound.
●
Chorus Pre Delay (0.0~100.0ms)—Adjusts the delay between the
incoming direct signal and the moment when the chorus starts
working.
●
Chorus Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Chorus Depth (0~127)—Modulation intensity.
●
Chorus Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the chorus sound (W).
●
Level (0~127)—Output level.
31. DST‰ Flanger
This effect connects distortion and a flanger effect in series.
●
Distortion Drive (0~127)—Degree of distortion. Also changes
the volume.
●
Distortion Panpot (L64~0~63R)—Stereo location of the distor-
tion sound.
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Flanger Depth (0~127)—Modulation intensity.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Level (0~127)—Output level.
32. DST‰ Delay
This effect connects distortion and a delay effect in series.
●
Distortion Drive (0~127)—Degree of distortion. Also changes
the volume.
●
Distortion Panpot (L64~0~63R)—Stereo location of the distor-
tion sound.
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
33. EH‰ Chorus
This effect connects an enhancer and a chorus in series.
●
Enhancer Sens (0~127)—Sensitivity of the enhancer.
●
Enhancer Mix Level (0~127)—Level of the overtones generated
by the enhancer.
●
Chorus Pre Delay (0.0~100.0ms)—Adjusts the delay between the
incoming direct signal and the moment when the chorus starts
working.
●
Chorus Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Chorus Depth (0~127)—Modulation intensity.
●
Chorus Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the chorus sound (W).
●
Level (0~127)—Output level.
34. EH‰ Flanger
This effect connects an enhancer and a flanger in series.
●
Enhancer Sens (0~127)—Sensitivity of the enhancer.
●
Enhancer Mix Level (0~127)—Level of the overtones generated
by the enhancer.
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Flanger Depth (0~127)—Modulation intensity.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Level (0~127)—Output level.
35. EH‰ Delay
This effect connects an enhancer and a delay in series.
●
Enhancer Sens (0~127)—Sensitivity of the enhancer.
●
Enhancer Mix Level (0~127)—Level of the overtones generated
by the enhancer.
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
BK-7m_UK.book Page 111 Tuesday, January 4, 2011 9:25 AM
… 111 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland BK-7M BACKING MODULE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland BK-7M BACKING MODULE in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland BK-7M BACKING MODULE

Roland BK-7M BACKING MODULE Additional guide - English - 10 pages

Roland BK-7M BACKING MODULE Additional guide - German - 10 pages

Roland BK-7M BACKING MODULE User Manual - German - 124 pages

Roland BK-7M BACKING MODULE User Manual - Dutch - 128 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info