622366

Roland ADA-7000 Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
8
Front and Rear Panels
5MANUAL Button
Selects whether operation of the front panel PHANTOM buttons / PAD buttons /
INPUT sensitivity knobs will be enabled or disabled. If you want to enable operation of
these buttons/knobs, make the MANUAL indicator light.
If you wish to remotely control the ADA-7000 from a device connected via
the R-BUS connector, make the MANUAL indicator go dark.
6 CLOCK SOURCE Button
Selects the source of the sampling clock.
Turn down the volume on all devices connected to the R-BUS (RMDB2)
connector, RCA output jacks, and XLR output connectors (on the rear panel)
before operating this button.
R-BUS (RMDB2):
The ADA-7000 will operate according to the sampling clock of the device (e.g., digital
mixer or digital recorder) connected to the rear panel R-BUS connector. When a clock
signal is input from the R-BUS connector, the R-BUS indicator will light, and the
SAMPLING FREQ indicator for that sampling frequency will light. If no clock is being
input from the R-BUS connector, the R-BUS indicator will blink. If you have selected “R-
BUS (RMDB2)” as the sampling clock of the ADA-7000, you must set the master clock of
the connected device to be other than the R-BUS to which that ADA-7000 is
connected.
WORD CLOCK:
The ADA-7000 will operate according to the word clock signal that is connected to the
rear panel WORD CLOCK connector. When a clock is being input from the WORD
CLOCK connector, the WORD CLOCK indicator will light, and the SAMPLING FREQ
indicator for that frequency will light. If no clock is being input from the WORD CLOCK
connector, the WORD CLOCK indicator will blink. If you have selected “WORD
CLOCK” as the sampling clock of the ADA-7000, you must set the master clock of the
connected device to be the R-BUS to which that ADA-7000 is connected.
INTERNAL:
Select this when you want the ADA-7000 to operate on its own internal clock. Use the
SAMPLING FREQ button to set the sampling frequency. If you have selected
“INTERNAL” as the sampling clock of the ADA-7000, you must set the master clock of
the connected device to be the R-BUS to which that ADA-7000 is connected.
7 SAMPLING FREQ Button
If CLOCK SOURCE is set to “INTERNAL,” this selects the sampling frequency at which
the ADA-7000 will operate.
The ADA-7000 allows you to select a sampling frequency of 96 kHz. This is in
order to support 96 kHz compatible equipment that will become available in
the future. At present (December 1999), no devices with a 96 kHz compatible
R-BUS connector are available. For details, please contact your nearest
Roland Service Center, authorized Roland distributor, or your dealer.
8POWER Switch
This turns the power of the ADA-7000 on/off.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland ADA-7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland ADA-7000 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info