622366
10
Zoom out
Zoom in
Previous page
1/24
Next page
10
Front and Rear Panels
TERMINATOR Switch:
Turn this on if the ADA-7000 is the last device in the word clock signal chain. Normally
you will leave this turned on. Turn this off only if you are using a relay connector to
distribute the word signal to other devices.
fig.3a.e
OUT:
This outputs the sampling clock on which the ADA-7000 is operating. Use this when you
want another device to synchronize to the sampling clock on which the ADA-7000 is
operating.
3 R-BUS (RMDB2) Connector
This is an 8-in/8-out 24 bit digital audio connector. Connect it to another device that has
an R-BUS connector (e.g., Roland digital mixer or Roland digital recorder).
Connect the R-BUS (RMDB2) connector only to an R-BUS equipped device.
To avoid malfunctions, never connect it to a SCSI connector, an RS-232C
connector, or a parallel connector, even if the connector has the same
shape. Use a special R-BUS (RMDB2) cable to make connections.
RMDB II, RMDB2 and R-BUS are the same standard of Roland corporation.
4 RCA OUTPUT Connectors 1–8 (-10 dBu)
Connect an RCA phono type plug here to output the same analog signal (+4 dBu) as from
the XLR output (converted to consumer level).
5 XLR/TRS INPUT Connectors 1–8
Connect either an XLR type or TRS phone plug (not both) here to input an analog signal.
Phantom power can be supplied to the XLR input jacks. To turn the phantom power on/
off, use the front panel PHANTOM buttons.
* Always turn the phantom power off when connecting any device other than condenser
microphones that require phantom power. You risk causing damage if you mistakenly supply
phantom power to dynamic microphones, audio playback devices, or other devices that don’t
require such power. Be sure to check the specifications of any microphone you intend to use by
referring to the manual that came with it.
(This instrument’s phantom power: 48 V DC, 14 mA/ch Max)
6 XLR OUTPUT Connectors 1–8
Connect an XLR type plug here to output the analog signal (+4 dBu).
Sampling Clock Master
WORD CLOCK SLAVE
ADA-7000
Digtal Tape Recorder
TERMINATOR
SWITCH: OFF
CLOCK SOURCE: WORD CLOCK
WORD CLOCK IN
Connector
WORD CLOCK IN
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland ADA-7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland ADA-7000 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info