512472
27
Zoom out
Zoom in
Previous page
1/60
Next page
27
Wire position
Zones setup
Press GO
Main display -
Press ‘GO
Settings
Press GO
PressGO
Mow zone: Base
Press GO
Press ‘GO’ and follow
Child guard
Press GO
Wire position
Press GO
Scroll down until
Settings’is displayed
Scroll up until ’Wire
position’ is displayed
PressGO
Wire position
Wire position
Press GO to test
Zones setup
Press GO
Zones setup
Press GO
Zones setup
Press GO
Main display -
Press ‘GO
Settings
Press GO
PressGO
Mow zone: Base
Press GO
Mow zone: Base
Press GO
Press ‘GO’ and follow
Robomow while following
the Perimeter Wire
Child guard
Press GO
Wire position
Press GO
Scroll down until
Settings’is displayed
Scroll up until ’Wire
position’ is displayed
PressGO
Take the Perimeter Switch and squeeze the
tabs on both sides of the Perimeter Switch,
(as shown in figure 1.42A) and remove the
back cover from the Perimeter Switch.
Connect the power supply plug to the
Perimeter Switch board (see figure 1.42B)
and reassemble the Perimeter Switch.
Connect the power supply to a regular
household receptacle 230 Volts AC;
The Power Supply is for indoor use only, thus
place it in a dry location, which is well
ventilated (do not cover it with plastic bag); be
sure the power supply and the connection to
the low voltage cable are in a dry place and
not exposed to water and rain.
Press the ‘ON’ button. A small flashing green light next to the ‘ON button indicates that the
system is on and functioning properly. The Perimeter Switch also has indicators for a
disconnected/broken perimeter wire and for
poor wire splicing. Figure 1.43
The Perimeter Switch has an automatic shutoff feature, eliminating the need for you to turn it off
after each use. It will shut itself off after 12 hours of operation. You may manually turn the
perimeter switch off by pressing the ‘
ON’ button continuously for 3 seconds. A beep will be heard
after the three seconds, indicating you may release the button and the switch is off.Test the
perimeter wire setup by choosing the ‘
Wire position’ menu as shown in figure 1.44. Robomow
will follow the wire, while the mowing motor is switched off to prevent any damage to the
perimeter wire after the initial setup; Walk along the side of the Robomow while it is following the
edge until completing one loop of the perimeter without striking any object; If Robomow collides in
obstacle, it stops and drives back to allow you adjusting the wire position.
Figure 1.43
Perimeter Switch
Operating Panel
Flashing light indicates
the system is on
Indicates poor splicing of
perimeter wires or perimeter
wire, which is too long
Indicates a
disconnected/broken wire
ON button
Figure 1.44
Testing the Perimeter
Wire position
Figure
1.42A
Figure 1.42B
Connect the power supply plug
to the Perimeter Switch board
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM510 in the language / languages: English as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM510

Robomow RM510 User Manual - German - 60 pages

Robomow RM510 User Manual - Dutch - 60 pages

Robomow RM510 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info