512472
26
Zoom out
Zoom in
Previous page
1/60
Next page
26
Figure 1.40
Inserting and Fastening
Perimeter Wire to Connector
Figure 1.41
Plug the plot connector into
the Perimeter Switch
Using a small flat
blade screwdriver,
tighten the screw
to secure the perimeter
wire into the connector
1.7.3 Laying Out The Perimeter Wire
Now, knowing the Perimeter Switch location, you can begin the setup of the Perimeter Wire, as
was explained in articles 1.2 and 1.3. The perimeter wire setup in a Base and non-Base zone is
identical in terms of placement and fastening;
At the location of the perimeter switch, strip back 5 mm (0.2 inches) of insulation from the wire end.
Insert the wire end to the left side of the plot connector, as shown in figure 1.39 and tighten the
screw.
Peg/fix the beginning of the wire where the Perimeter Switch will be located;
Lay the wire from the Perimeter Switch to the lawn; be sure to leave enough wire at the beginning
to close the loop;
Start laying the wire to the counterclockwise direction when standing inside the lawn, as show in
Figure 1.39.
1.7.4 Completing And Testing The Setup
Once the perimeter wire is completed and pegged to the ground, the last step to complete is
attaching the Perimeter Switch to the perimeter wires and testing the setup.
Pull the two loose perimeter wire leads taut and peg them down to the ground (figure 1.36),
adjacent to one another, as you move away from the perimeter and towards the Perimeter Switch
location (use the same pegs to attach the two wires from the lawn to the Perimeter Switch
location).
At the location of the perimeter switch, cut the loose perimeter wire so both wires are of equal
length, removing any excess wire. Strip back
5 mm (0.2 in) of insulation from the wire end. Insert
the wire end to the free hole in the connector and tighten the screws as shown in figure 1.40.
Plug the perimeter wire connector into the Perimeter Switch (see figure 1.41)
Figure 1.39
Connecting the wire end to the
left side of the connector and
p
erimeter wire la
y
out direction
Perimeter wire layout
in clockwise direction (as view from
the inner side of the lawn)
Connect the wire end to
the left side of the plot
connector (when looking
towards the screws)
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM510 in the language / languages: English as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM510

Robomow RM510 User Manual - German - 60 pages

Robomow RM510 User Manual - Dutch - 60 pages

Robomow RM510 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info