520094

Robbe Futaba FX-40 Manual

83
Zoom out
Zoom in
Previous page
1/105
Next page
Model menu
Snap roll
Multi-motor
FX-40
The servo transit speed of all three control surfaces can be
entered individually for each direction, separately for the
‘there’ and ‘back’ directions. A separate programming mask is
provided in the second display level, as shown below.
Mark the appropriate field, and enter the desired value using
the arrow buttons. The adjustment range is 0 to 27 increments.
The highest number equates to a servo travel time of up to
nine seconds.
The screen shot below shows a typical servo run time set-up:
When you have completed the programming of a snap roll
manoeuvre, it is fundamentally essential to check everything
very carefully on the model itself.
18.20 MULTI-MOTOR
SETTINGS FOR MULTI-MOTOR MODELS
This function enables you to define the most important set-
tings for contr
olling the motors in a model air
craft with up to
four power plants. These settings are as follows:
• Motor cut-off functions (Motor off)
• Idle settings (Idle 2)
• Idle-up (Auto-rotation)
• Full-throttle trims (Trim max.)
• Idle trims (Trim idle)
To enter values for these settings you must first activate each
of the throttle servos (THR, THR2), and then enter the servo
position as a percentage.
With the ‘Power model’ type already set, mark the ‘Multi-
motor’ option in the Model menu. The screen display now
looks like this:
This menu will differ according to the particular model type
you have selected. The number of throttle channels displayed
on the screen is dictated by the number defined in the model
configuration. Our example shows two (maximum: four).
The first step is to activate the whole function for each throttle
channel (THR, THR2 etc.) in the Status line: mark the field, and
the display changes from ‘INH’ (inactive) to ‘ON’.
After this you can enter the settings for ‘Motor off’ and ‘Idle 2’
for each motor: the first step is to activate the function in the
Status line, and then enter the servo position (Posi.). Mark the
appropriate field to activate the function, then enter the posi-
tion in the form of a percentage value. After marking the field
you can a new value using the arrow buttons. The adjustment
range is 0% to 50%; the default setting is 17%. Pressing
‘Reset’ restores the default setting.
In the bottom line you will see the Auto-rotation (Motor Hold)
option, which can be activated individually for each motor.
Mark the appropriate field: the screen displays ‘ON’, and the
throttle servos run to the values set in the ‘Motor pos’ window.
This option sets one motor to a particular value, so that you
can adjust a second motor independently of it.
In the second level of the display you can set the values for the
trims - for full-throttle and idle - separately for each motor. The
required value is entered as a percentage figure in the ‘Rate’
line, using the arrow buttons. A separate field contains the pre-
fix, so you can reverse the direction of the servos if necessary
to suit your installation. The adjustment range is 0% to 30% in
each case. The default setting is 0%; pressing ‘Reset’ restores
that setting.
82
… 83 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FX-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FX-40 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FX-40

Robbe Futaba FX-40 User Manual - German - 105 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info