520094
65
Zoom out
Zoom in
Previous page
1/105
Next page
Model menu
Fixed-wing model aircraft
FX-40
You will find two button fields labelled ‘Current position’ (Cur.
pos.); these are used to call up and adjust the current posi-
tion of the throttle stick for the lower range from 0 to 49%
(min.) and for the upper range from 50 to 100% (max.). The
percentage values are displayed in their respective fields.
This screen shot shows a typical example of programming for
this sub-menu.
Settings for particular throttle states
The software of the FX-40 provides two fixed throttle states
which you can adjust and call up at any time; these have
alr
eady been described in the Base menu.
- Motor cut-of
f function (motor off): Section 16.12, page 48
- Idle-up (Idle 2): Section 16.13, page 48
In this menu you can program the settings for actuating the
needle valve for these throttle states. When you activate
one of these functions, the throttle servo runs to a particular
position. At the same time the needle valve setting varies so
that the mixture is optimum for the new carburettor setting.
The settings are entered as percentage values using the
familiar procedure: mark the field, and enter the value using
the arrow buttons. In each case the setting is immediately
displayed.
When you want to return to the first screen of this option, sim-
ply mark the ‘2/2’ button field in the top right corner.
18. MODEL MENUS (FIXED-WING MODELS)
In this Section we analyse the settings which are specific to
fixed-wing model aircraft. The options cover
ed here are those
which have not already been discussed in Section 17 (see
page 54). From the main screen, activate the Model menu by
touching the field bearing the image of the model aircraft: the
overview of the model menus is now displayed. The options
included in the select menu vary according to the model type
you have chosen. The following illustration shows an overview
of the model menus for fixed-wing model aircraft.
In this Section we discuss those options which not yet been
analysed. To guide us through the possible functions we will
take a fully equipped model glider as the basis for the Model
menu. This means that the options specific to power models
are not covered; they are discussed in the following section.
Aileron diff. = Differential aileron travel
Flap settings = Wing flap adjustments
Ail. -> flap = Aileron -> camber-changing flap mixer
Ail. -> brake flap = Aileron -> brake flap
Aileron -> rudder = Aileron -> rudder mixer
Airbrake -> elevator = Airbrake ? elevator mixer
Rudder -> aileron = Rudder -> aileron mixer
Spoiler = Camber-changing flap mixer
Elevator -> spoiler = Elevator -> flap mixer
Flap -> elevator = Flap -> elevator mixer
Butterfly = Butterfly (crow) mixer
Trim Mix 1 and 2 = Trim mixers 1 and 2
Gyro = Gyro settings
V-tail = V-tail mixer
Ailvator = Divided elevators with aileron function
Winglet = Winglet mixer for flying wing models
Motor = Settings for electric motors
Rudder -> elevator = Rudder -> elevator mixer
Snap roll = Snap roll
Multi motor = Pre-sets for models with two or more
motors
64
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FX-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FX-40 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FX-40

Robbe Futaba FX-40 User Manual - German - 105 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info