520097
71
Zoom out
Zoom in
Previous page
1/119
Next page
71
CURVE PROGRAMMABLE MIXES (
PROG.MIX5-8
)(
HELI
:
PROG.MIX5-6
):
Your 10C’s
ACRO
/
GLID
programs contain four separate curve programmable mixes.
HELI
contains two. There are a variety
of reasons you might want curve mixes . usually where a linear mix doesn’t t your needs along the whole range. One pre-
programmed curve mix is the
THROTTLE-NEEDLE
function. This curve is adjustable at 5 points, allowing you to adjust the
motors tuning at 5 points along its RPM range.
One programmable curve mix defaults to
RUDDER-AILERON
. A linear mix that keeps the model from rolling in knife-edge is
probably too much aileron when rudder is applied in level ight. Create a curve mix and set all 5 points to match the linear
mix. Inhibit the linear mix, then adjust the curve to get the right response all along the rudder channel’s travel.
Adjustability: for detailed de nitions, see Linear Programmable Mixes and Glossary.
ACRO
/
GLID
Defaults: The 4 programmable curve mixes default to the most frequent choices, but can be set to any channel.
PROG.MIX5
rudder-to-aileron for roll coupling compensation (
GLID
mixes default to aileron-to-elev.)
PROG.MIX6
rudder-to-aileron for roll coupling compensation (
GLID
mixes default to aileron-to-elev.)
PROG.MIX7
rudder-to-elevator for pitch coupling compensation (
GLID
mixes default to elevator-to-airbrake.)
PROG.MIX8
rudder-to-elevator for pitch coupling compensation (
GLID
mixes default to elevator-to-airbrake.)
HELI
Defaults:
PROG.MIX5
aileron-to-elevator for coordinated turns
PROG.MIX6
aileron-to-elevator for coordinated turns
Master: The controlling channel can only be a channel. Cannot be
OFFSET
or dial.
Trim: not available in curve mixes.
Offset: not available in curve mixes.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info