520097

Robbe Futaba FF-10 Manual

70
Zoom out
Zoom in
Previous page
1/119
Next page
70
GOAL of EXAMPLE: STEPS: INPUTS:
Set up a
FLAP-ELEV
mix:
ON
when SWITCH C is in the down
position.
No elevator movement when fl aps move
up (spoilers),
5% elevator movement when flaps
move down,
LINK
should be
ON
if model has twin
elevator servos. Otherwise,
LINK
remains
OFF
.
(Flap has no trim lever, so
TRIM
is not
an option.)
Open an unused programmable mix.
(Ex: use
PROG.MIX3
since it is already
set-up for
FLAP-ELEVATOR
.)
for 1 second.
(If
BASIC
, again.)
C
to
PROG.MIX-
.
C
to
3 >
.
Activate the function.
C
to
MIX
. to
ON
.
Choose master and slave channels.
(Ex: no need to change
MASTER/SLAVE
.)
already
CH6
already
CH2
Optional: set Master as
OFST
or
VR(A-E)
.
See above for details.
C
to
MASTER
. to desired choice.
Set LINK and TRIM as needed.
(Ex: leave
LINK OFF
,
TRIM
not available.)
Assign SWITCH and position.
(Ex: change from
E
to
C
,
DOWN
.)
C
to
SW
. to
C
.
C
to
POSI
. to
DOWN
.
Optional: set switch to
STk-THR
to
activate mix with THROTTLE STICK.
(See above for details.)
C
to
SW
. to
STk-THR
.
C
to
POSI
.
THROTTLE STICK to desired
point.
for 1 second to set.
Optional: set switch position to
NULL
.
Makes mix active at all times. Not
compatible with
STk-THR
.
C
to
POSI
. to
NULL
.
Set rates. (Ex: Lo=
0%
, Hi=
5%
.)
C
to
RATE
.
VR(A) past center. Leave at
0%
.
VR(A) past center. to
5%
.
Set
OFFSET
, if needed. (Ex:
0
.)
C
to
OFFSET
. Leave at
0%
.
Close menu.
Where next? Adjust servo
END POINTs
: see p. 39.
Setup dual/triple rates and exponential (
D/R
,
EXP
): see p. 42.
Set up additional programmable mixes, ex:
RUDDER
-
AILERON
: see p. 68.
View numerous additional mix setups: www.futaba-rc.com\faq\
Other Examples:
•
RUD-ELEV
(
ACRO
/
GLID
) mix: Compensate for pitching up or down when rudder is applied.
•
AIL-RUD
mix (
ACRO
): Coordinate turns by applying rudder automatically with aileron input. All model types.
•
ELEV-PIT
(
HELI
) mix: compensate for the loss of lift of tilting the model.
… 70 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info