726821

REMKO RVS DC serie 50-80-130-180 Manual

19
Zoom out
Zoom in
Previous page
1/44
Next page
Installation Instructions for qualified personnel
■
Observe the manuals for
the indoor units and chillers
when installing the entire
system.
■
The indoor units and
chillers work independently.
A connecting line between
the two is not necessary.
■
Select an installation location
which allows air to flow
freely through the inlet and
outlet. See section "Minimum
clearances".
■
Do not install the unit in
the immediate vicinity of
devices which generate
intensive thermal radiation.
Installation in the vicinity
of thermal radiation reduces
the unit output.
■
Lift the unit only at intended
lifting points. Never apply loads
to the medium piping.
■
The medium connection lines,
valves and connections must be
insulated impervious to vapour
diffusion.
■
Seal off open lines to prevent
dirt getting in.
■
Make all electrical connections
in accordance with applicable
DIN and VDE standards.
■
Always ensure the electrical
cables are properly connected
to the terminals.
Otherwise there is a risk of fire.
■
Comply with all regulations
governing structural and
building requirements and
conditions with regard to
the installation site.
■
In the selection of
the installation site, pay
attention to the site itself
and to any possible acoustic
reflection from surrounding
units.
■
To avoid the transmission of
vibrations to the installation
site, the units must be installed
on vibration absorbing material
or on vibration decoupled
foundations.
In doing so, make sure that
the lines are also vibration
decoupled.
■
If the installation site must
fulfil special sound emission
requirements, these must
be realised on-site when
appropriate adjustments can be
made.
In these cases, please consult an
appropriate acoustics expert.
■
The units are tested in
the factory and require
only electrical and hydraulic
installation by a suitable
specialist.
Important notes prior
to installation
■
The unit must be kept upright
when transporting to a higher
elevation:
■
Check the contents of
the packaging for completeness
and check the unit for visible
transport damage.
Report any damage immediately
to your contractual partner and
the shipping company.
■
If necessary, also insulate
the condensate drainage line
(only units with HP-function).
In dual systems with cooling
and heating modes, the
requirements of the current
Energy-Savings-Ordinance
(EnEV) are to be complied with.
Transport
■
Transport the unit in its original
packaging as close as possible
to the installation location.
You avoid transport damage
by doing so.
■
The units may only be moved
as installed (upright) using
appropriate transport gear
(Figure 1).
Secure against tipping!
1 Standing transport
19
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RVS DC serie 50-80-130-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RVS DC serie 50-80-130-180 in the language / languages: English as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RVS DC serie 50-80-130-180

REMKO RVS DC serie 50-80-130-180 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info