587723
20
Zoom out
Zoom in
Previous page
1/28
Next page
Unit installation
The indoor unit is attached by
means of a wall bracket, under
consideration of air discharge side
located in the lower part.
1. Mark the mounting points
on the statically permissible
building sections according to
the dimensions of the unit.
2. If necessary, remove the break
out opening on the housing.
3. Connect the refrigerant
pipes, electrical cables and
condensation line to the indoor
unit as described below.
4. Hang the indoor unit onto the
wall bracket by tilting it back
slightly and by pressing the
bottom part of the unit against
the bracket.
5. Check again to ensure that the
unit is level (Figure 4).
Installation
Installation should only be
performed by authorised
specialists.
NOTE
The units are factory filled with
dry nitrogen to check for leaks.
The pressurised nitrogen is
released when loosening the
union nuts.
CAUTION
Connection of refrigerant
pipes
The on-site connection of the
refrigerant pipes is made at the
rear of the unit.
If necessary, a reduction or
expansion needs to be installed on
the indoor unit.
These fittings are included as
standard with the indoor unit.
Once installed, the connections
should be insulated to make them
vapour diffusion proof.
4 Horizontal alignment
The wall bracket for the unit must
be attached with suitable screws
and anchors.
Condensation
connection
Due to the dew point shortfall,
condensation forms on the
vaporiser during the cooling
operation on the indoor unit.
Below the vaporiser is a collection
tray, which must be connected to
a drain.
The condensation line should
have a fall of min. 2 %. (Fig. 5).
If necessary, fit vapour diffusion
proof insulation.
The condensation line from
the unit should run freely
into the drainage pipe. If the
condensation runs directly into
a sewer pipe, install a trap to
prevent any unpleasant odours.
When operating the unit at
outdoor temperatures below
0 °C, ensure the condensation
line is laid to protect it against
frost. If necessary, install a pipe
heater.
After completed routing, check
for unobstructed condensation
discharge and ensure that a
permanent seal is provided.
The condensation hose is designed
to be installed on the left side
(view from front).
5
Condensation connection
Min. 2% drop
REMKO MXW
20
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MXW520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MXW520 in the language / languages: English as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MXW520

REMKO MXW520 User Manual - German - 28 pages

REMKO MXW520 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info