587906
37
Zoom out
Zoom in
Previous page
1/44
Next page
37
Type of faults
F8
F6
F4
F3
F2
F1
Brenner zündet nicht
Sicherheitsthermostat (STB)
Brennergebläse defekt
Fühler NTC1 oder NTC2
werden falsch angezeigt
Verriegelung der Steuerplatine
Flammenüberwachungsgerät
- Kabelverbindung zwischen Flammenüberwachungsgerät
und Steuerplatine überprüfen
- Parameter A1 und A2 müssen den Werten der Tabelle im
Abschnitt “Auswechseln der Steuerplatine” entsprechen
- Flammenüberwachungsgerät defekt
- Gasversorgung und Gaskomponenten überprüfen
(siehe auch F1)
- Bei wiederholten Verriegelungen Steuerplatine ersetzen
- Korrekte Position der Brücke auf NTC überprüfen
- Fühler NTC1 überprüfen
- Fühler NTC2 überprüfen (nur mit Temperaturregelung)
- Gasversorgung nicht vorhanden bzw. fehlerhaft
- Phase- und Nullleiter vertauscht
- Erdleiter fehlt oder falsch angeschlossen
- Zündelektrode defekt oder falsch eingebaut
- Überwachungselektrode defekt oder falsch eingebaut
- Flammüberwachungsgerät defekt
- Zündgasdüse verschmutzt oder falsche Dimension
- Umluftventilator defekt
- mangelhafte Kühlung des Wärmetauschers
- Kapillarrohr oder Fühler defekt
- Fühlerposition zu nahe am Wärmetauscher
- Sicherheitsthermostat auf elektr. Durchgang überprüfen
- Dichtungen defekt, warme Abgase kommen an den Fühler
Hinweis: Der Fühler ist nicht nur an der Spitze, sondern auf
seiner gesamten Kapillarrohrlänge sensibel
- Niederspannungskabel zum Brennergebläse defekt oder
nicht angeschlossen
- Parameter A1 und A2 müssen den Werten der Tabelle im
Abschnitt “Auswechseln der Steuerplatine” entsprechen
- Brennergebläse defekt
- Brennerplatine defekt
ERR
Fehlerhafte Verbindung mit
der Temperaturregelung
- Fehlerhaftes Verbindungskabel
- Elektromagnetische Störungen
- Fehlerhafte Temperaturregelung ATR-6
- Umgebungstemperatur der ATR-6 unter 0°C
Störung des Flammüberwachungs-
geräts wegen nicht erfolgter Zündung
des Brenners; die Steuerplatine
sorgt vor der Meldung der Störung
für eine Serie von automatischen
Entriegelungsversuchen.
Auslösung des Sicherheitsthermos-
taten. Falls die vom Thermostat
erfasste Temperatur zu hoch ist,
löst dieser aus und blockiert den
Betrieb des Gerätes.
Verbrennungsluft-Gebläse ist defekt
oder die Signalmeldung an die
Steuerplatine liegt außerhalb des
Toleranzbereichs hinsichtlich der
verlangten Drehzahl.
NTC1 Fühler defekt oder nicht ange-
schlossen - der Wert des Fühlers
liegt außerhalb des Messbereichs.
Wegen ständiger und wiederholter
erfolgloser Zündversuche für einen
vorbestimmten Zeitraum. Bei dieser
Störung leuchtet auch die LED zur
Störungssignalisierung direkt auf der
Steuerplatine.
Die Steuerplatine hat dem Flamm-
überwachungsgerät das Startsignal
übermittelt, aber das Signal des
erfolgten Starts nicht erhalten;
evtl. Flammenüberwachungsgerät
defekt.
We reserve the right to make changes to dimensions and design in the interest of technological advances.
- Circulation air fan faulty
- Inadequate cooling of the heat exchanger
- Capillary tube or sensor faulty
- Sensor positioned too close to heat exchanger
- Check safety thermostat for electrical continuity
- Seals faulty, warm exhaust gases make contact with the
sensor.
Note: The sensor is not only sensitive at its tip, but along its
entire length
Safety thermostat (STB)
Operation of safety thermostat.
If the temperature detected by
the thermostat is too high, the
same operates and blocks
operation of the unit.
- Gas supply not present or faulty
- Phase and neutral conductors interchanged
- Earth conductor missing or incorrectly connected
- Ignition electrode faulty or incorrectly fi tted
- Monitoring electrode faulty or incorrectly fi tted
- Flame monitoring device faulty
- Ignition gas nozzle clogged or incorrect size
Burner does not ignite
Fault of the fl ame monitoring
device due to burner ignition
failure; the control board makes
several automatic reset attempts
prior to signalling the fault.
- Low-voltage cable to burner fan faulty or not connected
- Parameters A1 and A2 must correspond to the values in the
table in section “Control board replacement”.
- Burner fan faulty
- Burner board faulty
Burner fan faulty
The combustion air fan is faulty or
the signal to the control board is
outside the tolerance range with
respect to the requested speed.
- Check jumper on NTC for correct position
- Check sensor NTC1
- Check sensor NTC2 (only with temperature control)
Sensor NTC1 or NTC2 is
incorrectly displayed
NTC1 sensor faulty or not
connected – the sensor value is
outside the measuring range
- Check gas supply and gas components (see also F1)
- Replace control board if interlocks persist
Control board interlock
Control board fault due to
constant and repeated
unsuccessful ignition attempts of
the unit for a predefi ned period.
- Check cable connection between fl ame monitoring device
and control board
- Parameters A1 and A2 must correspond to the values in
the table in section “Control board replacement”.
- Flame monitoring device faulty
Flame monitoring device
The control board sent the
starting signal to the fl ame
monitoring device, but did not
receive the started signal; it is
possible that the fl ame
monitoring device is faulty.
- Incorrect connection cable
- Electromagnetic interference
- Faulty temperature control ATR-6
- Ambient temperature of ATR-6 below 0°C
Incorrect connection to
temperature control
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO GPM 25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO GPM 25 in the language / languages: English as an attachment in your email.

The manual is 4,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO GPM 25

REMKO GPM 25 User Manual - German - 44 pages

REMKO GPM 25 User Manual - Dutch - 44 pages

REMKO GPM 25 User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info