587581
17
Zoom out
Zoom in
Previous page
1/28
Next page
Error indicated by flashing code
Display Cause Required action
88 flashes Power outage for 3 minutes Switch off and switch back on
E1 flashes Communication error display controller Contact specialist dealer
E2 flashes Circulation sensor on indoor unit faulty/tripped Contact specialist dealer
E3 flashes Frost protection sensor on indoor unit faulty/tripped Contact specialist dealer
E4 flashes Vaporiser fan motor speed too low/faulty Contact specialist dealer
E5 flashes No cooling/heating output after 30 minutes. Contact specialist dealer
E6 flashes Undervoltage protection has tripped Contact specialist dealer
E7 flashes Communication error
Reprogram (see chapter
“Programming when error E7 is indicated”)
Programming when error E7 is indicated
If error 07 "Communication error"
occurs, perform the following
programming procedure:
1. Prepare to reset the unit by
removing the batteries from the
remote control.
2. Press and hold / and put
the batteries back in the remote
control.
The display will show
"00 00 00"
3. If digit I is "0", proceed to
step "5".
4. If digit I is "1", press the
Programming E7
Digit I Digit II
Digit III Digit IV Digit V Digit VI
is displayed before continuing
with the programming
procedure!
10.
Point the transmitter on the IR
remote control at the receiver
on the indoor unit and press the
"ON/OFF" button until a beep
acknowledges that the signal
has been received. The first LED
on the right side flashes.
11.
After the acknowledgement
beep has sounded, remove
the batteries from the remote
control for approx. 1 minute.
Re-insert the batteries to
complete the programming
procedure. You can now select
the desired operating mode.
"MODE" button until digit I
changes to "0".
5. Program the 1st communication
code for digits I to VI by
pressing the following buttons
several times:
ATY 261: 04 54 05
ATY 351: 04 54 05
Verify that the correct code
is displayed before continuing
with the programming
procedure! 6. Press
the"MODE" button to save the
settings.
7. If the first digit is "1", proceed
to step "9".
8. If the first digit is "0", go back
to step "1." and repeat the
programming procedure.
9. Program the 2nd
communication code for digits I
to VI by pressing the following
buttons several times:
ATY 261: 1A 00 EA
ATY 351: 1A 00 Fb
Verify that the correct code
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ATY351 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ATY351 in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ATY351

REMKO ATY351 Additional guide - German - 1 pages

REMKO ATY351 User Manual - German - 28 pages

REMKO ATY351 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info