805760
22
Zoom out
Zoom in
Previous page
1/36
Next page
22
Commissioning
Filling and ushing the Remeha Flexistor
Ensure that all ttings and immersion heaters are correctly tted and tightened.
i) Open a hot tap furthest from the Remeha Flexistor.
ii) Open the mains stop cock to ll the unit. When water issues from the tap, allow to run for a few
minutes to thoroughly ush through any residue, dirt or swarf, then close tap.
iii) Open successive hot taps to purge any air from the system.
iv) Check all connections for leaks and rectify as necessary.
v) The Strainer housed within the Pressure Reducing Valve should be cleaned to remove
any debris that may have been ushed through the main supply pipe.
Check the operation of the Safety Valves
i) Slowly, manually open for a few seconds, the Temperature and Pressure Relief Valve
(T&P Valve) situated on the Remeha Flexistor unit. Check water discharged runs freely
away through the tundish and discharge pipe work. Close valve, ensure water ow stops
and valve reseats correctly.
ii) Repeat for the Pressure Relief Valve.
NOTE: The water discharged may be very hot.
Primary Heat source (when tted)
Connect up primary heat source as per manufacturers instructions. Fill up primary and second-
ary circuits, bleeding any air that may be trapped and check for leaks. Make sure secondary cir-
cuit has wholesome water only, the Flexistor range of cylinders do not have an internal heat ex-
changer. Take care that the Primary Heat source can handle the working pressure of the cylinder.
Auxiliary power supply (Immersion Heaters)
Switch on the electrical supply to the immersion heater(s) and allow the unit to heat up. Check
that the thermostat operates correctly. A storage temperature of approx. 60ºC is recommended,
install and set up immersions as per immersion heater tting instructions (36006161) . Check
that no water is discharged from either the Expansion Valve or Temperature and Pressure Relief
Valve during the heating cycle. The thermal cut-out is factory set to 80°C max for direct heating
Benchmarktm Log Book
On completion of the installation and commissioning procedures detailed in this Product Guide
the BenchmarkTM “Installation, Commissioning and Service Record Log” should be completed
and signed o󰀨 by the competent installer or commissioning engineer in the relevant sections. The
various system features, location of system controls, user instructions and what to do in the event
of a system failure should be explained to the customer. The customer should then countersign
the BenchmarkTM commissioning checklist to accept completion. The Service Record should be
lled in when any subsequent service or maintenance operation is carried out on the Remeha
Flexistor unit.
See pages 32 and 33 for BenchmarkTM logbook and service record
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha Flexistor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha Flexistor in the language / languages: English as an attachment in your email.

The manual is 2.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info