6
at room temperature for at least 2 hours before use.
I I. OPER A TION
Before Use
-
tive coatings, or any other obje cts or cabinets that could be damaged by steam,
humidity , or high temperatures. Before operating the appliance, ensure that the
outer and inner parts of the pressure multicooker have no dents, cracks or any
other visible damages. There should not be any obstructions between the heat-
ing element and the bowl.
Standby mode
The plugged in appliance has default standby mode setting; current time is
displayed in 24-hour format. If no button was pressed during one minute when
setting selected programme parameters, the appliance will switch to the stand-
by mode; all the pre vious settings will be cleared.
T o adjust the clock
T o adjust the current time:
1 . Press and hold “Hour/Min” button for several minutes in standb y mode.
indicator will be lit on the display; clock regist er indicator will be
2 .
Select clock value rotating adjustment ring this or other way . R epress
“Hour/Min” button to switch the register and turning the adjustment ring
adjust the minute value. Aft er maximum value is reached the adjustment
starts from beginning of the adjustment range.
3 . When time adjusting is complete do not press any buttons. The adjusted
time value will be saved in a few se conds.
Enable/disable audible signals
The REDMOND RMC -M13E/RMC -M23E/RMC-M33E multic ookers allow to enable/
disable audible signals, that accompany pressing the buttons and the end of
cooking process. T o disable/enable audible signals press and hold “ Cancel” but-
ton in standby mode.
Non-volatile memory
The REDMOND RMC -M13E/RMC -M23E/RMC-M33E multic ookers have non-vol-
-
utes in cooking mode) the applianc e saves all settings to the memory. The ap-
pliance will start operation on the interrupted stage. Press the “C ancel” button
if it is undesirable to the continue c ooking process. The appliance will switch to
the standby mode.
T o adjust cooking time
The REDMOND RMC -M13E/RMC -M23E/RMC-M33E multic ookers provide default
cooking time adjusting. Time int erval and range depend on selected cooking
programme.
1 .
Select the programme rotating the adjustment ring this or that way .
be displayed for every programme.
2 .
3 . Select the time value rotating adjustment ring this or that way . Repress
the “Hour/Min” button to switch the register and adjust minute value
turning the adjustment ring. After the maximum value is reached in
every register the adjustment starts from beginning of the adjustment
range.
Time Delay
The time delay function allows adjusting time b y which the dish will be ready .
The maximum time of delay is 24 hours in 15 minut es interval. It should be
taken into acc ount that Time of delay should be more than adjust ed cooking
time otherwise the programme will start the operation after pressing the “Star t/
Ke ep Warm” button.
1 .
Select the programme, adjust the cooking time if necessary . Adjust
2 .
Press the “Set” button. The “Time Delay” and the time value indicators will
3 . Adjust the time value rotating the adjustment ring. Repress the “Hour/
Min” button to switch the register and adjust the minute value turning
the adjustment ring. After the maximum value is reached in e very register
the adjustment starts from beginning of the adjustment range.
4 .
Press the “Start/Keep Warm” button. The appliance will swit ch to the Time
Delay mode, the “Time Delay” and the current time indicators will be lit.
Press the “Hour/Min” button to see the adjusted time by which the food
will be ready .
5 . Press the “C ancel” button to clear the current settings. The cooking pro-
gramme should be adjusted all over again.
K eep W arm function
This function automatically activat es in the end of cooking cycle and keeps the
disable the Ke ep Warm press and hold the “Start/Keep Warm” button (the “Keep
Warm” indicator will go out).
leave food heated for a long time, as it may lead to food overdrying and change
in its taste qualities.
-
grammes.
programmes — 4 hours.
Keep Warm disabled in advance
The Ke ep Warm mode may be disabled in advance if necessary . T o do so after the
start of cooking programme repress and hold the “Start/Keep W arm” button
until the “Keep Warm” indicator goes out.
In the same manner the Ke ep Warm function may be activated again (the “K eep
Warm” indicator will be lit up solid).
R eheat
Provides reheating c old meals:
1 . Fill the bowl with food and position it inside the appliance. Ensure it is
tightly c onnected to the heating element.
2 . Close the lid until it clicks into place. Plug in the appliance.
3 . Press the “R eheat” butt on. The “R eheat” indicator will light up solid, the
“Reheat” function will be activated and direct minute countdown will start.
Model RMC -M13E RMC -M23E
RMC -M33E
Bowl type RB-C302 RB-C502
RB-C602
5 . Housing
6 . Container for c ondensate collection
7. Control panel with display
8 . Adjustment ring
9 . Pow er switch
10. Lid release button
11. Steaming container
12. Measuring cup
13. Serving spoon
14. Stirring paddle
15. Po wer cord
Elements of control panel
A2
1 . Display .
2 . Cooking programmes indicators.
3 .
“Hour/Min” button— switches on current time adjustment mode; to select
hour/minute value in current time adjustment modes, cooking time and
time delay .
4 . “Reheat” button — to enable Reheat function (in standby mode).
5 .
“Start/Keep W arm” button with “Star t” and “K eep W arm” indicat ors— to
start cooking programme; to disable Ke ep Warm in advance.
6 . Adjustment ring: to select cooking programme; to adjust current time/
cooking time/ time delay; to adjust temperature in “MUL TICOOK” pro-
gramme. T urn the ring clockwise to increase the value, turn the ring
counterclockwise t o reduce the value. 16 switches per 360°degree rotation
may be performed.
7. “Ke ep Warm” indicator is lit up when K eep Warm mode is enabled.
8 .
“C ancel” button — to stop cooking programme operation; to clear previous
settings; to enable/disable audible signals (in standby mode).
9 . “Set” button — to enable parameter adjusting mode; to switch to c ooking
temperature adjusting mode (in “MUL TICOOK” programme) / Time Delay .
10.
“Start” indicator lights up during cooking programme operation and Time
Display
A . “Timer” indicator — is lit when adjusting cooking time/ during programme
operation.
B .
“Time Delay” indicator — is lit when adjusting Time Delay / during appliance
operation in Time Delay .
C . Disabled audible signals indicator .
D . Ke ep Warm indicator .
E . “Reheat” indicator — is lit during Reheat function operation.
F . T emperature value indicator in “MUL TICOOK” programme.
I . PRIOR T O THE FIRST USE
Carefully unpack the device, remove all packaging materials and stickers exc ept
the one with the unit’ s serial number.
Wipe all interior and exterior surfac es of the unit with a soft, damp cloth. Wash
appliance is normal. In such case, clean the device.