7894

Rebox RE-2250MG Manual

41
Zoom out
Zoom in
Previous page
1/47
Next page
www.rebox.tv
41
a quick scan and will find all channels that have been listed by Canal Digitaal. The found
channels will be stored in your receiver in a logical order. “Free only” (Free to Air) only or
“All Channels” to find all available channels on the satellite.
• Scan channels from the satellite: Your receiver allows you to use 4 types of channel
scans:
• AutoScan (Red Button): Starts the automatic channel scan by using the parameters that
you have set in the “Channel Set-up menu”. Please also refer to page 18, “5.1.1
Channel Organiser Menu”.
• Net. Scan (Green Button): “Network Search” Performs network search for a
transponder.
• Transponder Scan (Yellow Button): Search channels from current specific transponder.
• PID (Blue Button): You can search a specific channel by entering the PID value of a
channel. If you press the Blue (PID) button, the PID screen is displayed. Enter the PID
value and press the Blue button again. To cancel the PID value, press BACK on the
remote control or press the Blue (PID) button to search the channel. You should enter
V-PID, A-PID and P-PID as described in “Editing channels from the channel list”
(Described in section 5.1.1)
Tip:
Check the level and quality of the signal bar before searching any channels. The signal level of the TP
of the current satellite is displayed. The green bar is displayed if the settings are correct, otherwise the red bar is
displayed and you cannot get the channel. In the latter case, check if your dish is aimed at the selected satellite or
if the DiSEqC switch of the LNB overlaps with another satellite. Also, change the Frequency with the Left/Right
button until the Green bar is displayed to get the valid transponder. If you press the Red (Auto Scan), Green (Net.
Scan), Yellow (TP Scan), or Blue (PID) button the channel searching status is displayed (Figure 24)
5.1.4.3.1 Positioner Set-up (if you are using a Motorised positioner with DiSEqC1.2)
If you are using a motorised positioner with DiSEqC 1.2 you will have to set the positions of the satellites you want
to scan. This function is available only if in the “LNB Set-up” menu and the LNB Dish field is set to “Moved”. (As
described in “LNB Set-up” (Described in section 5.1.4.2).
Before you start:
1. Make sure that your installer has set the centre position of your dish.
2. Make sure that the mechanical limits of your motor are set, so that no damage can be done to
your dish by moving it too far to the East/West.
3. Make sure you set the highest Symbol Rate (Ksymbols/sec) for your chosen transponder (TP).
The Signal level and Quality indicator will help you set up the best dish position possible.
4. Use your UP/DOWN buttons to select the “Dish Position" field in the “Channel Set-up” menu.
( Note that the LNB dish in the LNB setup menu is set to “Motorized”.)
5. Press the OK button and the “Positioner Set-up” Menu will be displayed.
6. Start setting the position of the selected satellite.
7. Use your UP/DOWN buttons to go to field “Centre” and use your Left/Right buttons to put the
centre field to “On”.
8. Press OK, and your dish will move to the centre position. It takes your dish maximum 30 seconds
to move to its central position.
9. To know in which direction you will need to move your dish, you will need to know the position of
the satellite you want it to position to.
10. If correctly installed, your installer has set the centre position of your dish to the “true” South if in
the Northern hemisphere and to “true” North if in the Southern Hemisphere.
11. If for instance you want to set the position for Astra 19.2°East, you know that you will have to
move your dish to the left using the Left button. If you want to set the position for instance to
Eutelsat 12.5°West, you know that you will have to move your dish to the right using the Right
button. (As viewed from the rear of the dish)
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rebox RE-2250MG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rebox RE-2250MG in the language / languages: Dutch as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info